N7/h6 Fit Tolerances
ISO Fits · Shaft-basis fits (h shaft)
N7/h6: Transition fit, Shaft-basis fits (h shaft). At ⌀25 mm the hole is −7 / −28 µm, the shaft 0 / −13 µm, giving a maximum clearance of 6 µm and a minimum clearance of −28 µm (negative = interference). The table below lists the limits for every ISO size range up to 500 mm.
- Fit type
- Transition
- Max. clearance at ⌀25 mm
- 6 µm0.00024 in0.00024 in6 µm
- Min. clearance at ⌀25 mm (− = interference)
- −28 µm−0.00110 in−0.00110 in−28 µm
Drawing
N7/h6 specifications
| Fit type | Transition |
|---|---|
| Hole limits at ⌀25 mm (µm) | −7 / −28 |
| Shaft limits at ⌀25 mm (µm) | 0 / −13 |
| Max. clearance at ⌀25 mm | 6 µm0.00024 in |
| Min. clearance at ⌀25 mm (− = interference) | −28 µm−0.00110 in |
N7/h6 limits for every size range (µm)
| Size (mm) | Hole ES / EI | Shaft es / ei | Max. clearance | Min. clearance | Type |
|---|---|---|---|---|---|
| ≤ 3 | −4 / −14 | 0 / −6 | +2 | −14 | transition |
| 3–6 | −4 / −16 | 0 / −8 | +4 | −16 | transition |
| 6–10 | −4 / −19 | 0 / −9 | +5 | −19 | transition |
| 10–18 | −5 / −23 | 0 / −11 | +6 | −23 | transition |
| 18–30 | −7 / −28 | 0 / −13 | +6 | −28 | transition |
| 30–50 | −8 / −33 | 0 / −16 | +8 | −33 | transition |
| 50–80 | −9 / −39 | 0 / −19 | +10 | −39 | transition |
| 80–120 | −10 / −45 | 0 / −22 | +12 | −45 | transition |
| 120–180 | −12 / −52 | 0 / −25 | +13 | −52 | transition |
| 180–250 | −14 / −60 | 0 / −29 | +15 | −60 | transition |
| 250–315 | −14 / −66 | 0 / −32 | +18 | −66 | transition |
| 315–400 | −16 / −73 | 0 / −36 | +20 | −73 | transition |
| 400–500 | −17 / −80 | 0 / −40 | +23 | −80 | transition |
Shaft-basis transition fit with likely interference: bushes and ring parts on a common ground shaft.
Other fits of the same type (Transition)
All ISO fits
Sources
- ISO 286-1:2010, Geometrical product specifications (GPS): ISO code system for tolerances on linear sizes, Part 1: Basis of tolerances, deviations and fits
- ISO 286-2:2010, Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
- ANSI B4.2-1978 (R2020): Preferred metric limits and fits
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.