H7/js6 Fit Tolerances
ISO Fits · Hole-basis fits (H hole)
H7/js6: Transition fit, Hole-basis fits (H hole). At ⌀25 mm the hole is +21 / 0 µm, the shaft +6.5 / −6.5 µm, giving a maximum clearance of 27.5 µm and a minimum clearance of −6.5 µm (negative = interference). The table below lists the limits for every ISO size range up to 500 mm.
- Fit type
- Transition
- Max. clearance at ⌀25 mm
- 27.5 µm0.00108 in0.00108 in27.5 µm
- Min. clearance at ⌀25 mm (− = interference)
- −6.5 µm−0.00026 in−0.00026 in−6.5 µm
Drawing
H7/js6 specifications
| Fit type | Transition |
|---|---|
| Hole limits at ⌀25 mm (µm) | +21 / 0 |
| Shaft limits at ⌀25 mm (µm) | +6.5 / −6.5 |
| Max. clearance at ⌀25 mm | 27.5 µm0.00108 in |
| Min. clearance at ⌀25 mm (− = interference) | −6.5 µm−0.00026 in |
H7/js6 limits for every size range (µm)
| Size (mm) | Hole ES / EI | Shaft es / ei | Max. clearance | Min. clearance | Type |
|---|---|---|---|---|---|
| ≤ 3 | +10 / 0 | +3 / −3 | +13 | −3 | transition |
| 3–6 | +12 / 0 | +4 / −4 | +16 | −4 | transition |
| 6–10 | +15 / 0 | +4.5 / −4.5 | +19.5 | −4.5 | transition |
| 10–18 | +18 / 0 | +5.5 / −5.5 | +23.5 | −5.5 | transition |
| 18–30 | +21 / 0 | +6.5 / −6.5 | +27.5 | −6.5 | transition |
| 30–50 | +25 / 0 | +8 / −8 | +33 | −8 | transition |
| 50–80 | +30 / 0 | +9.5 / −9.5 | +39.5 | −9.5 | transition |
| 80–120 | +35 / 0 | +11 / −11 | +46 | −11 | transition |
| 120–180 | +40 / 0 | +12.5 / −12.5 | +52.5 | −12.5 | transition |
| 180–250 | +46 / 0 | +14.5 / −14.5 | +60.5 | −14.5 | transition |
| 250–315 | +52 / 0 | +16 / −16 | +68 | −16 | transition |
| 315–400 | +57 / 0 | +18 / −18 | +75 | −18 | transition |
| 400–500 | +63 / 0 | +20 / −20 | +83 | −20 | transition |
Transition fit, mostly slight clearance: hubs, couplings and pulleys with a key that should be assembled with a light mallet, bearing inner rings under light loads.
Other fits of the same type (Transition)
All ISO fits
Sources
- ISO 286-1:2010, Geometrical product specifications (GPS): ISO code system for tolerances on linear sizes, Part 1: Basis of tolerances, deviations and fits
- ISO 286-2:2010, Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
- ANSI B4.2-1978 (R2020): Preferred metric limits and fits
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.