Metric Flat Washer Size Chart

Inside diameter, outside diameter and thickness of metric plain washers: ISO 7089 normal series (dimensionally the same as DIN 125-A) and ISO 7093 large series, often sold as fender or DIN 9021 washers. An M8 washer is 8.4 × 16 × 1.6 mm.

24 sizesChecked 2026-11-155 sources
M3 – M8M3⌀7 / ⌀9M4⌀9 / ⌀12M5⌀10 / ⌀15M6⌀12 / ⌀18M8⌀16 / ⌀24M10 – M24 (smaller scale)M10⌀20 / ⌀30M12⌀24 / ⌀37M16⌀30 / ⌀50M20⌀37 / ⌀60M24⌀44 / ⌀72
Filled ring: ISO 7089 normal washer; dashed circle: ISO 7093 large (fender) washer for the same bolt. Two scales; numbers are the outside diameters in mm.Drawn to scale · Dimensions in mmDimensions in inches

Size chartTap a size for its drawing and full specs

24 of 24
Sized₁Inside diametermmind₂Outside diametermminhThicknessmminOutside diameter, large (ISO 7093)mminThickness, large (ISO 7093)mmin
M1.61.70.06740.1570.30.012——
M22.20.08750.1970.30.012——
M2.52.70.10660.2360.50.020——
M33.20.12670.2760.50.02090.3540.80.031
M44.30.16990.3540.80.031120.47210.039
M55.30.209100.39410.039150.59110.039
M66.40.252120.4721.60.063180.7091.60.063
M88.40.331160.6301.60.063240.94520.079
M1010.50.413200.78720.079301.1812.50.098
M12130.512240.9452.50.098371.45730.118
M14150.591281.1022.50.098——
M16170.669301.18130.118501.96930.118
M18190.748341.33930.118——
M20210.827371.45730.118602.36240.157
M22230.906391.53530.118——
M24250.984441.73240.157722.83550.197
M27281.102501.96940.157——
M30311.220562.20540.157923.62260.236
M33341.339602.36250.197——
M36371.457662.59850.1971104.33180.315
M42451.772783.07180.315——
M48522.047923.62280.315——
M56622.4411054.134100.394——
M64702.7561154.528100.394——

How washers are sized

A washer is named after the bolt it fits, not after its hole: an M8 washer has an 8.4 mm hole. The hole equals the ISO 273 fine clearance hole for that size, so the washer centres reasonably on the bolt but still slides over the thread.

Measure the outside diameter and thickness with a caliper to tell the series apart: an M8 washer with a 16 mm outside diameter is normal series, one with 24 mm is large series (ISO 7093). Thickness of normal-series washers steps in standard sheet gauges: 0.3, 0.5, 0.8, 1, 1.6, 2, 2.5, 3, 4, 5 mm.

ISO 7090 is the same washer as ISO 7089 with a chamfer on one side (DIN 125-B); ISO 7092 is a small series for cheese and socket head screws, with a smaller outside diameter.

About Flat Washers

A flat washer spreads the clamping load of the bolt head or nut over a larger area, protects the surface from the turning nut, and bridges oversized or slotted holes. ISO 7089 normal-series washers in the chart fit hex bolts and nuts; product grade A, hardness class 200 HV for property classes up to 8.8, 300 HV for 10.9 bolts.

ISO 7089 replaced DIN 125-A with the same dimensions up to M36. Above M36 they part ways: ISO 7089 washers for M42, M48, M56 and M64 have 45, 52, 62 and 70 mm bores, while DIN 125 tables list 43, 50, 58 and 66 mm (with the same outside diameters). Only the ISO preferred sizes are shown above M36; check the supplier's sheet for M39, M45, M52 and M60.

Large-series washers (ISO 7093-1) have about three times the bolt diameter as outside diameter: use them on wood, plastics, thin sheet and slotted holes. The DIN 9021 washers sold under the same name are almost identical; the M5 DIN 9021 washer is 1.2 mm thick instead of 1 mm. ISO 7093 lists only the first-choice sizes, so the second-choice rows (M14, M18 …) have no large-series values.

Questions

What size is an M8 washer?

An ISO 7089 / DIN 125 M8 washer has an 8.4 mm hole, 16 mm outside diameter and 1.6 mm thickness. The large (fender) M8 washer, ISO 7093, is 24 mm across and 2 mm thick.

What are the dimensions of an M6 washer?

6.4 mm inside, 12 mm outside, 1.6 mm thick (ISO 7089). Large series: 18 mm outside, 1.6 mm thick.

Is DIN 125 the same as ISO 7089?

For M1.6 to M36, yes: same inside and outside diameters and thickness. Above M36 the ISO bores are larger (M48: 52 mm ISO vs 50 mm DIN). ISO 7089 replaced DIN 125-A; DIN 125-B with a chamfer became ISO 7090.

What is a fender washer in metric?

The ISO 7093 large-series washer, also sold as DIN 9021. Its outside diameter is about three times the bolt size: M6 → 18 mm, M8 → 24 mm, M10 → 30 mm.

Why is the washer hole larger than the bolt?

So it slides over the thread and any burrs: the hole equals the ISO 273 fine clearance (M8 → 8.4 mm, M10 → 10.5 mm, M12 → 13 mm).

Sources

  1. ISO 7089:2000, Plain washers, normal series, product grade A
  2. ISO 7093-1:2000, Plain washers, large series, part 1: product grade A
  3. ISO 7093-2:2000, Plain washers, large series, part 2: product grade C (outside diameters and thickness)
  4. fasten.it and Boltport: ISO 7089 dimension tables (M42–M64 cross-check)
  5. ISO 887:2000, Plain washers for metric bolts, screws and nuts, general plan

Values last checked against these sources on November 15, 2026. · How we check data

Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.