Self-Tapping Screw Sizes (ST2.2–ST6.3, Sheet Metal Screws)

Self-tapping screws cut or form their own thread in sheet metal and plastic. The ST size is the thread diameter in millimetres. ST4.2 is 4.22 mm, the same as a #8, and has a coarse pitch of 1.4 mm (about 18 threads per inch).

8 sizesChecked 2026-11-153 sources

Size chartTap a size for its drawing and full specs

8 of 8
SizedMajor diametermminPPitchmminInch gauge equivalentdkPan head dia. ISO 7049 (max)mminkPan head height ISO 7049 (max)mminCross recess
ST2.22.240.0880.80.031#24.00.1571.60.063PH0 / PZ0
ST2.92.900.1141.10.043#45.60.2202.40.094PH1 / PZ1
ST3.53.530.1391.30.051#67.00.2762.60.102PH2 / PZ2
ST3.93.910.1541.30.051#77.50.2952.80.110PH2 / PZ2
ST4.24.220.1661.40.055#88.00.3153.10.122PH2 / PZ2
ST4.84.800.1891.60.063#109.50.3743.70.146PH2 / PZ2
ST5.55.460.2151.80.071#1211.00.4334.00.157PH3 / PZ3
ST6.36.250.2461.80.071#1412.00.4724.60.181PH3 / PZ3

How to read ST sizes and choose a pilot hole

ST stands for the tapping screw thread of ISO 1478. The number is the nominal thread diameter: ST2.9, ST3.5, ST3.9, ST4.2, ST4.8, ST5.5 and ST6.3 correspond to the inch gauges #4, #6, #7, #8, #10, #12 and #14, with the same thread. A designation like ISO 7049 – ST4.2 × 16 – C means a cross recessed pan head, 16 mm long, with point type C (pointed).

Point type C has a sharp cone and starts in thin sheet; type F is flat with a short taper for thicker material; type R is rounded. Self-drilling screws (ISO 15480–15483) have a drill point and need no pilot hole in steel up to their rated thickness.

The pilot hole depends on sheet thickness and material, so makers give tables per thickness: thin steel sheet needs a hole close to the thread root, thicker or harder sheet a larger one. Check the screw maker's table; there is no single correct pilot size for an ST size.

About Self-Tapping Screws

Tapping screws are used for sheet metal, profiles, ducts and plastic housings where a nut or tapped hole is impractical. The thread is coarser than a machine screw thread (ST4.2: 1.4 mm pitch vs. 0.7 mm for M4), which gives more material in the engagement in thin sheet.

The pan head dimensions of ISO 7049 match the ISO 7045 machine screw heads closely, so pan head tapping screws and machine screws look alike. Check the thread before using one in a tapped hole. Countersunk (ISO 7050) and raised countersunk (ISO 7051) versions use the same ST threads.

Hex washer head and self-drilling versions are common in construction (roofing, cladding); their thread sizes are the same ST series.

Questions

What is an ST4.2 screw in inches?

A #8 sheet metal screw: 4.22 mm (0.164 in) major diameter, 1.4 mm pitch, about 18 threads per inch.

What does ST mean on a screw?

Self-tapping (tapping screw) thread to ISO 1478. The number is the thread diameter in mm: ST3.5 = 3.53 mm max.

Can I use a self-tapping screw in a tapped hole?

No. The ST thread has a different pitch and profile from the metric machine thread (ST4.2: 1.4 mm pitch; M4: 0.7 mm).

What Phillips bit for an ST3.5 screw?

PH2 (or PZ2). ST2.9 takes PH1, ST5.5 and ST6.3 PH3.

Sources

  1. ISO 1478:1999, Tapping screws thread
  2. ISO 7049:2011, Cross recessed pan head tapping screws
  3. fasten.it: DIN EN ISO 15481 drilling screws (pan head, tapping thread) table

Values last checked against these sources on November 15, 2026. · How we check data

Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.