Sheet Metal Gauge Chart: Steel, Galvanized, Stainless, Aluminum
Thickness of sheet metal by gauge number for standard steel, galvanized steel, stainless steel and aluminum. Gauge is not a unit: the same number means a different thickness in each material. 16 gauge is 0.0598 in in steel, 0.0635 in galvanized, 0.0625 in stainless and 0.0508 in aluminum.
Size chartTap a size for its drawing and full specs
| Gauge | tStandard steel (MSG)mmin | tGalvanized steelmmin | tStainless steelmmin | tAluminum (B&S / AWG)mmin |
|---|---|---|---|---|
| 3 gauge | 6.070.2391 | — | 6.350.2500 | 5.830.2294 |
| 4 gauge | 5.690.2242 | — | 5.950.2344 | 5.190.2043 |
| 5 gauge | 5.310.2092 | — | 5.550.2187 | 4.620.1819 |
| 6 gauge | 4.940.1943 | — | 5.160.2031 | 4.110.1620 |
| 7 gauge | 4.550.1793 | — | 4.760.1875 | 3.670.1443 |
| 8 gauge | 4.180.1644 | 4.270.1681 | 4.370.1719 | 3.260.1285 |
| 9 gauge | 3.800.1495 | 3.890.1532 | 3.970.1562 | 2.910.1144 |
| 10 gauge | 3.420.1345 | 3.510.1382 | 3.570.1406 | 2.590.1019 |
| 11 gauge | 3.040.1196 | 3.130.1233 | 3.180.1250 | 2.300.0907 |
| 12 gauge | 2.660.1046 | 2.750.1084 | 2.780.1094 | 2.050.0808 |
| 13 gauge | 2.280.0897 | 2.370.0934 | 2.380.0937 | 1.830.0720 |
| 14 gauge | 1.900.0747 | 1.990.0785 | 1.980.0781 | 1.630.0641 |
| 15 gauge | 1.710.0673 | 1.800.0710 | 1.790.0703 | 1.450.0571 |
| 16 gauge | 1.520.0598 | 1.610.0635 | 1.590.0625 | 1.290.0508 |
| 17 gauge | 1.370.0538 | 1.460.0575 | 1.430.0562 | 1.150.0453 |
| 18 gauge | 1.210.0478 | 1.310.0516 | 1.270.0500 | 1.020.0403 |
| 19 gauge | 1.060.0418 | 1.160.0456 | 1.110.0437 | 0.910.0359 |
| 20 gauge | 0.910.0359 | 1.010.0396 | 0.950.0375 | 0.810.0320 |
| 21 gauge | 0.840.0329 | 0.930.0366 | 0.870.0344 | 0.720.0285 |
| 22 gauge | 0.760.0299 | 0.850.0336 | 0.790.0312 | 0.640.0253 |
| 23 gauge | 0.680.0269 | 0.780.0306 | 0.710.0281 | 0.570.0226 |
| 24 gauge | 0.610.0239 | 0.700.0276 | 0.640.0250 | 0.510.0201 |
| 25 gauge | 0.530.0209 | 0.630.0247 | 0.560.0219 | 0.450.0179 |
| 26 gauge | 0.450.0179 | 0.550.0217 | 0.470.0187 | 0.400.0159 |
| 27 gauge | 0.420.0164 | 0.510.0202 | 0.440.0172 | 0.360.0142 |
| 28 gauge | 0.380.0149 | 0.470.0187 | 0.400.0156 | 0.320.0126 |
| 29 gauge | 0.340.0135 | 0.440.0172 | 0.360.0141 | 0.290.0113 |
| 30 gauge | 0.300.0120 | 0.400.0157 | 0.320.0125 | 0.250.0100 |
No exact match. The nearest sizes:
How sheet metal gauge works
A higher gauge number means thinner sheet: 10 gauge steel is 0.1345 in (3.42 mm), 20 gauge 0.0359 in (0.91 mm). The steps are not even: between 10 and 11 gauge the thickness drops 0.0149 in, between 28 and 29 only 0.0014 in.
Each material has its own gauge table. Standard steel uses the Manufacturers' Standard Gauge, which is really a weight scale: 16 ga = 2.5 lb/ft², and thickness = weight ÷ 41.82 lb/ft² per inch. Galvanized sheet adds the zinc, about 0.0037 in, to the same weight scale. Stainless is usually listed to the old U.S. Standard Gauge of 1893 (16 ga = 1/16 in). Aluminum, copper and brass use the Brown & Sharpe gauge, which is the same series as AWG wire.
Because of that, a gauge number alone is ambiguous. Engineering drawings and purchase orders should state the decimal thickness (e.g. 0.060 in or 1.5 mm) and the material standard. Mills roll to a tolerance of a few thousandths of an inch around the nominal value, so a micrometer reading of 0.058 in on steel is still 16 gauge.
About Sheet Metal Gauge
To identify an unknown sheet, measure it with a micrometer or caliper away from the edge, then look up the material column. A sheet of 0.063 in could be 16 ga galvanized, 16 ga stainless or about 14 ga aluminum (0.0641 in). A magnet separates carbon steel from aluminum and most austenitic stainless.
Typical uses: 26–24 ga steel for HVAC ductwork and flashing, 22–20 ga for duct and appliance panels, 18–16 ga for car body panels and enclosures, 14–11 ga for brackets, trailers and structural sheet. Aluminum sheet for vehicles and boats is usually ordered by decimal thickness (0.040, 0.063, 0.080, 0.125 in) rather than gauge.
Metric countries specify sheet directly in millimetres (0.5, 0.75, 1.0, 1.25, 1.5, 2.0, 3.0 mm). When converting a US drawing, pick the nearest stocked metric thickness and check bend radii and fastener grip; 16 ga (1.52 mm) is normally replaced by 1.5 mm, 18 ga (1.21 mm) by 1.2 or 1.25 mm, 20 ga (0.91 mm) by 0.9 or 1.0 mm.
Other gauge systems you may meet
Wire and sheet in the UK historically used the Standard Wire Gauge (SWG, Imperial Standard Wire Gauge of 1883), where 16 SWG is 0.064 in (1.63 mm). Zinc sheet has its own zinc gauge, and jewelry and hypodermic tubing use the Birmingham (Stubs) gauge. None of these match the tables above, so check which gauge an old drawing or catalogue means.
Questions
How thick is 16 gauge steel?
0.0598 in (1.52 mm) for standard uncoated steel. Galvanized 16 ga is 0.0635 in (1.61 mm), stainless 0.0625 in (1.59 mm) and aluminum 0.0508 in (1.29 mm).
Which is thicker, 14 gauge or 16 gauge?
14 gauge. Lower gauge numbers are thicker: 14 ga steel is 0.0747 in (1.90 mm), 16 ga is 0.0598 in (1.52 mm).
Why is aluminum gauge different from steel gauge?
The gauges come from different historical systems. Steel gauge is based on weight per square foot; aluminum uses the Brown & Sharpe (AWG) series. So 16 ga aluminum is 0.0508 in while 16 ga steel is 0.0598 in.
How do I convert gauge to mm?
Look up the thickness in inches for your material and multiply by 25.4. Examples for steel: 10 ga = 3.42 mm, 12 ga = 2.66 mm, 14 ga = 1.90 mm, 16 ga = 1.52 mm, 18 ga = 1.21 mm, 20 ga = 0.91 mm, 22 ga = 0.76 mm.
What gauge is 1/8 inch steel?
11 gauge steel is 0.1196 in, the closest to 1/8 in (0.125 in). In stainless, 11 gauge is exactly 0.1250 in. Plate thicker than about 3/16 in is ordered by fraction, not gauge.
Sources
- ASTM A480 / A240 (stainless sheet) and ASTM A653 (galvanized): ordering by decimal thickness; gauge tables as published by distributors
- Engineers Edge: Sheet metal gauge sizes table (standard steel, galvanized, stainless, aluminum)
- ASTM B258: Standard nominal diameters of solid round wires (AWG / Brown & Sharpe formula)
- U.S. Standard Gauge for sheet and plate iron and steel, Act of Congress of March 3, 1893 (15 U.S.C. 206)
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.