Bicycle Bottom Bracket Standards Chart

A bottom bracket is defined by the frame's shell: its width and its inside diameter, and whether it is threaded, takes pressed-in cups, or takes bearings directly. Measure both with a caliper and the standard is almost always unambiguous: a 68 mm shell with a 34.8 mm thread is BSA, a 68 mm smooth 46 mm bore is PF30, an 86.5 mm smooth 41 mm bore is BB86.

15 sizesChecked 2026-11-155 sources

Size chartTap a size for its drawing and full specs

15 of 15
StandardWShell widthmminAlternative shell widthmmin⌀Shell inside diametermminThreadCrank spindles available
Threaded shells
BSA / English682.68732.8734.81.3701.370″ × 24 TPI24 mm, GXP 24/22, DUB 28.99, 30 mm (narrow-bearing BBs), square taper
Italian702.76—361.417M36 × 24 TPI24 mm, GXP 24/22, DUB 28.99, square taper
French682.68—351.378M35 × 1mostly square taper (vintage cartridge BBs)
Swiss682.68—351.378M35 × 1mostly square taper (vintage cartridge BBs)
T47 (outboard)682.68732.87471.850M47 × 124 mm, GXP 24/22, DUB 28.99, 30 mm
T47 internal (86.5 / 85.5)86.53.4185.53.37471.850M47 × 124 mm, GXP 24/22, DUB 28.99
Press-fit shells (cups pressed into the frame)
PF30682.68732.87461.811—30 mm native; 24 mm, GXP and DUB with matching BBs
BB8686.53.41—411.614—24 mm, GXP 24/22, DUB 28.99
BB9291.53.6089.53.52411.614—24 mm, GXP 24/22, DUB 28.99
BB386 EVO86.53.41—461.811—30 mm (386 EVO-length cranks); DUB and 24 mm with matching BBs
BBright793.11—461.811—30 mm BBright-length cranks; DUB BBright; 24 mm with adapter BBs
Direct-fit shells (bearings pressed straight into the frame)
BB30682.68732.87421.654—30 mm native; 24 mm, GXP and DUB with adapter BBs
BB30A732.87—421.654—30 mm (BB30A-length cranks); DUB and 24 mm with adapter BBs
BB90 (Trek)90.53.56—371.457—24 mm; DUB with matching BB
BB95 (Trek)95.53.76—371.457—24 mm; DUB with matching BB

How to identify a bottom bracket

Remove the cranks and measure the shell width across the faces of the frame shell (not over the BB cups) and the inside diameter of the shell. Then check whether the inside is threaded. Width and diameter together identify almost every standard in the chart.

Threaded: 68 or 73 mm wide with a ~34.8 mm thread is BSA (English); 70 mm with a 36 mm thread is Italian; a 47 mm thread is T47. French and Swiss (35 × 1 mm) only appear on older European bikes. Smooth 41 mm bore: BB86 (86.5 mm wide) or BB92 (91.5 mm). Smooth 42 mm with circlip grooves: BB30 (68/73 mm) or BBright direct-fit (79 mm). Smooth 46 mm: PF30 (68/73), BB386 EVO (86.5) or BBright (79). 37 mm with a step and no circlips: Trek BB90/95.

The crank spindle is a separate question. Shimano road and MTB cranks use a 24 mm steel spindle; SRAM GXP is 24 mm on the drive side, stepped to 22 mm on the non-drive side; SRAM DUB is 28.99 mm; Cannondale, Race Face, Rotor, FSA and others use 30 mm. A bottom bracket is chosen for both the shell and the spindle, e.g. "BSA 68, DUB" or "PF30, 24 mm".

About Bottom Brackets

Threaded shells were the only kind until the 2000s. They are easy to service with a cup tool and creak-free when the threads are clean and greased. BSA (also called English or ISO) is by far the most common: 1.370 in × 24 TPI, with a left-hand thread on the drive side so pedalling does not unscrew the cup. T47 keeps the threads but uses a 47 mm bore, big enough for 30 mm spindles with inboard bearings. That is why many new frames moved back to it.

Press-fit designs moved the bearings into the shell to allow a wider, stiffer frame junction and larger spindles. In direct-fit shells (BB30, BB90/95) the bearings press straight into the frame, so shell tolerances directly decide bearing fit. In press-fit shells (PF30, BB86/92, BB386 EVO, BBright) the bearings sit in cups, which tolerate imperfect bores better but can creak if the shell is out of round.

Many crank/shell combinations are possible with the right bottom bracket. A 30 mm spindle needs a shell bore of at least 42 mm (BB30) or 46 mm (PF30, BB386 EVO) for bearings inside, or outboard bearings on a threaded shell. A 24 mm or DUB spindle fits almost every shell with the matching BB, including 30 mm-capable shells via adapter or reducer bottom brackets.

Spindle length is a third compatibility check: wide shells (BB386 EVO, BBright) need cranks made for that width or a spindle long enough to span it. The crank maker's compatibility chart lists which shells each crank length supports.

Thread directions

BSA, Swiss and T47 are threaded left-hand on the drive side (the cup removes clockwise) and right-hand on the non-drive side. Italian and French shells are right-hand on both sides, which is why Italian drive-side cups can loosen over time. If in doubt, look for markings on the cup: "1.37 × 24" with an arrow or "LH".

Shell width variants

BSA shells are 68 mm on road bikes and 73 mm on mountain bikes; 83 mm (downhill) and 100 or 120 mm (fat bikes) also exist. BB92 shells for mountain bikes are 91.5 mm (an 89.5 mm version exists for 68-mm-equivalent frames). Trek's T47 internal shells are 85.5 mm, other makers' 86.5 mm; the same bottom brackets fit both in most cases. A 77 mm asymmetric T47 shell (68 mm on the drive side, 86.5 mm-style on the non-drive side) is also in use.

Questions

What is the difference between BSA 68 and 73?

Only the shell width: 68 mm on road and gravel frames, 73 mm on most mountain bikes. The thread (1.370″ × 24 TPI) is the same. Most external-bearing BSA bottom brackets fit both, using spacers on 68 mm shells as the crank maker specifies.

Is PF30 the same as BB30?

No. Both are 68 or 73 mm wide and designed for 30 mm spindles, but BB30 has a 42 mm bore with the bearings pressed straight in, and PF30 a 46 mm bore for bearings in cups.

Can I use a SRAM DUB crank on a BSA frame?

Yes, with a DUB BSA bottom bracket. DUB (28.99 mm) bottom brackets exist for BSA, Italian, T47, BB30, PF30, BB86/92, BB90/95, BB386 EVO and BBright shells.

What is the difference between BB86 and BB92?

Width only: BB86 shells are 86.5 mm (road), BB92 shells 91.5 mm (mountain bikes). Both have a 41 mm bore and use the same type of Shimano press-fit cups for 24 mm spindles.

How do I tell T47 from BSA?

Measure the shell's inside thread diameter: about 47 mm for T47, about 34.8 mm for BSA. T47 shells look much larger inside, and their cups need a large-diameter tool.

Sources

  1. Park Tool: Bottom bracket standards and terminology
  2. Sheldon Brown: Threaded bottom bracket crib sheet
  3. Sheldon Brown: Unthreaded bottom bracket crib sheet
  4. Wheels Manufacturing: Bottom bracket standards chart
  5. BikeRadar: The complete guide to bottom bracket standards

Values last checked against these sources on November 15, 2026. · How we check data

Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.