H11/h11 Fit Tolerances
ISO Fits · Hole-basis fits (H hole)
H11/h11: Clearance fit, Hole-basis fits (H hole). At ⌀25 mm the hole is +130 / 0 µm, the shaft 0 / −130 µm, giving a maximum clearance of 260 µm and a minimum clearance of 0 µm (negative = interference). The table below lists the limits for every ISO size range up to 500 mm.
- Fit type
- Clearance
- Max. clearance at ⌀25 mm
- 260 µm0.01024 in0.01024 in260 µm
- Min. clearance at ⌀25 mm (− = interference)
- 0 µm0.00000 in0.00000 in0 µm
Drawing
H11/h11 specifications
| Fit type | Clearance |
|---|---|
| Hole limits at ⌀25 mm (µm) | +130 / 0 |
| Shaft limits at ⌀25 mm (µm) | 0 / −130 |
| Max. clearance at ⌀25 mm | 260 µm0.01024 in |
| Min. clearance at ⌀25 mm (− = interference) | 0 µm0.00000 in |
H11/h11 limits for every size range (µm)
| Size (mm) | Hole ES / EI | Shaft es / ei | Max. clearance | Min. clearance | Type |
|---|---|---|---|---|---|
| ≤ 3 | +60 / 0 | 0 / −60 | +120 | 0 | clearance |
| 3–6 | +75 / 0 | 0 / −75 | +150 | 0 | clearance |
| 6–10 | +90 / 0 | 0 / −90 | +180 | 0 | clearance |
| 10–18 | +110 / 0 | 0 / −110 | +220 | 0 | clearance |
| 18–30 | +130 / 0 | 0 / −130 | +260 | 0 | clearance |
| 30–50 | +160 / 0 | 0 / −160 | +320 | 0 | clearance |
| 50–80 | +190 / 0 | 0 / −190 | +380 | 0 | clearance |
| 80–120 | +220 / 0 | 0 / −220 | +440 | 0 | clearance |
| 120–180 | +250 / 0 | 0 / −250 | +500 | 0 | clearance |
| 180–250 | +290 / 0 | 0 / −290 | +580 | 0 | clearance |
| 250–315 | +320 / 0 | 0 / −320 | +640 | 0 | clearance |
| 315–400 | +360 / 0 | 0 / −360 | +720 | 0 | clearance |
| 400–500 | +400 / 0 | 0 / −400 | +800 | 0 | clearance |
Loose locational fit for parts where only rough centring is needed: hinge pins, parts that are welded or pinned afterwards.
Other fits of the same type (Clearance)
H11/c11Clearance · 370 µm · 110 µmH9/d9Clearance · 169 µm · 65 µmH9/e9Clearance · 144 µm · 40 µmH8/f7Clearance · 74 µm · 20 µmH7/f7Clearance · 62 µm · 20 µmH7/g6Clearance · 41 µm · 7 µmH7/h6Clearance · 34 µm · 0 µmH8/h7Clearance · 54 µm · 0 µmC11/h11Clearance · 370 µm · 110 µmD9/h9Clearance · 169 µm · 65 µmF8/h7Clearance · 74 µm · 20 µmG7/h6Clearance · 41 µm · 7 µm
All ISO fits
Sources
- ISO 286-1:2010, Geometrical product specifications (GPS): ISO code system for tolerances on linear sizes, Part 1: Basis of tolerances, deviations and fits
- ISO 286-2:2010, Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
- ANSI B4.2-1978 (R2020): Preferred metric limits and fits
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.