Gear Module Chart
The module m is the size of a metric gear tooth: pitch diameter divided by the number of teeth. Every other tooth dimension follows from it (circular pitch πm, addendum 1 m, dedendum 1.25 m, whole depth 2.25 m), so two gears mesh only if their modules and pressure angles match.
Module chartTap a module for its drawing and gear calculator
| Size | Series | pCircular pitch (πm)mmin | sTooth thickness (πm/2)mmin | haAddendum (1 m)mmin | hfDedendum (1.25 m)mmin | hWhole depth (2.25 m)mmin | DPEquivalent diametral pitch (25.4/m) | Nearest standard DP |
|---|---|---|---|---|---|---|---|---|
| Fine modules below 1 (DIN 780 / JIS B 1701) | ||||||||
| Module 0.3 | fine | 0.9430.0371 | 0.4710.0186 | 0.30.0118 | 0.3750.0148 | 0.6750.0266 | 84.67 | 80 |
| Module 0.4 | fine | 1.2570.0495 | 0.6280.0247 | 0.40.0157 | 0.50.0197 | 0.90.0354 | 63.5 | 64 |
| Module 0.5 | fine | 1.5710.0618 | 0.7850.0309 | 0.50.0197 | 0.6250.0246 | 1.1250.0443 | 50.8 | 48 |
| Module 0.6 | fine | 1.8850.0742 | 0.9430.0371 | 0.60.0236 | 0.750.0295 | 1.350.0531 | 42.33 | 40 |
| Module 0.7 | fine | 2.1990.0866 | 1.1000.0433 | 0.70.0276 | 0.8750.0344 | 1.5750.0620 | 36.29 | 40 |
| Module 0.75 | fine | 2.3560.0928 | 1.1780.0464 | 0.750.0295 | 0.93750.0369 | 1.68750.0664 | 33.87 | 32 |
| Module 0.8 | fine | 2.5130.0989 | 1.2570.0495 | 0.80.0315 | 10.0394 | 1.80.0709 | 31.75 | 32 |
| Module 0.9 | fine | 2.8270.1113 | 1.4140.0557 | 0.90.0354 | 1.1250.0443 | 2.0250.0797 | 28.22 | 32 |
| ISO 54 modules, series I and II | ||||||||
| Module 1 | I | 3.1420.1237 | 1.5710.0618 | 10.0394 | 1.250.0492 | 2.250.0886 | 25.4 | 24 |
| Module 1.125 | II | 3.5340.1391 | 1.7670.0696 | 1.1250.0443 | 1.40630.0554 | 2.53130.0997 | 22.58 | 24 |
| Module 1.25 | I | 3.9270.1546 | 1.9640.0773 | 1.250.0492 | 1.56250.0615 | 2.81250.1107 | 20.32 | 20 |
| Module 1.375 | II | 4.3200.1701 | 2.1600.0850 | 1.3750.0541 | 1.71880.0677 | 3.09380.1218 | 18.47 | 18 |
| Module 1.5 | I | 4.7120.1855 | 2.3560.0928 | 1.50.0591 | 1.8750.0738 | 3.3750.1329 | 16.93 | 16 |
| Module 1.75 | II | 5.4980.2164 | 2.7490.1082 | 1.750.0689 | 2.18750.0861 | 3.93750.1550 | 14.51 | 14 |
| Module 2 | I | 6.2830.2474 | 3.1420.1237 | 20.0787 | 2.50.0984 | 4.50.1772 | 12.7 | 12 |
| Module 2.25 | II | 7.0690.2783 | 3.5340.1391 | 2.250.0886 | 2.81250.1107 | 5.06250.1993 | 11.29 | 12 |
| Module 2.5 | I | 7.8540.3092 | 3.9270.1546 | 2.50.0984 | 3.1250.1230 | 5.6250.2215 | 10.16 | 10 |
| Module 2.75 | II | 8.6390.3401 | 4.3200.1701 | 2.750.1083 | 3.43750.1353 | 6.18750.2436 | 9.24 | 10 |
| Module 3 | I | 9.4250.3711 | 4.7120.1855 | 30.1181 | 3.750.1476 | 6.750.2657 | 8.47 | 8 |
| Module 3.5 | II | 10.9960.4329 | 5.4980.2164 | 3.50.1378 | 4.3750.1722 | 7.8750.3100 | 7.26 | 8 |
| Module 4 | I | 12.5660.4947 | 6.2830.2474 | 40.1575 | 50.1969 | 90.3543 | 6.35 | 6 |
| Module 4.5 | II | 14.1370.5566 | 7.0690.2783 | 4.50.1772 | 5.6250.2215 | 10.1250.3986 | 5.64 | 6 |
| Module 5 | I | 15.7080.6184 | 7.8540.3092 | 50.1969 | 6.250.2461 | 11.250.4429 | 5.08 | 5 |
| Module 5.5 | II | 17.2790.6803 | 8.6390.3401 | 5.50.2165 | 6.8750.2707 | 12.3750.4872 | 4.62 | 5 |
| Module 6 | I | 18.8500.7421 | 9.4250.3711 | 60.2362 | 7.50.2953 | 13.50.5315 | 4.23 | 4 |
| Module 7 | II | 21.9910.8658 | 10.9960.4329 | 70.2756 | 8.750.3445 | 15.750.6201 | 3.63 | 4 |
| Module 8 | I | 25.1330.9895 | 12.5660.4947 | 80.3150 | 100.3937 | 180.7087 | 3.18 | 3 |
| Module 9 | II | 28.2741.1132 | 14.1370.5566 | 90.3543 | 11.250.4429 | 20.250.7972 | 2.82 | 3 |
| Module 10 | I | 31.4161.2368 | 15.7080.6184 | 100.3937 | 12.50.4921 | 22.50.8858 | 2.54 | 2.5 |
| Module 11 | II | 34.5581.3605 | 17.2790.6803 | 110.4331 | 13.750.5413 | 24.750.9744 | 2.31 | 2.5 |
| Module 12 | I | 37.6991.4842 | 18.8500.7421 | 120.4724 | 150.5906 | 271.0630 | 2.12 | 2 |
| Module 14 | II | 43.9821.7316 | 21.9910.8658 | 140.5512 | 17.50.6890 | 31.51.2402 | 1.81 | 1.75 |
| Module 16 | I | 50.2661.9790 | 25.1330.9895 | 160.6299 | 200.7874 | 361.4173 | 1.59 | 1.5 |
| Module 18 | II | 56.5492.2263 | 28.2741.1132 | 180.7087 | 22.50.8858 | 40.51.5945 | 1.41 | 1.5 |
| Module 20 | I | 62.8322.4737 | 31.4161.2368 | 200.7874 | 250.9843 | 451.7717 | 1.27 | 1.25 |
| Module 22 | II | 69.1152.7211 | 34.5581.3605 | 220.8661 | 27.51.0827 | 49.51.9488 | 1.15 | 1.25 |
| Module 25 | I | 78.5403.0921 | 39.2701.5461 | 250.9843 | 31.251.2303 | 56.252.2146 | 1.02 | 1 |
No exact match. The nearest sizes:
How the tooth dimensions follow from the module
The module is defined on the pitch circle: m = d / z, where d is the pitch diameter and z the number of teeth. A gear with 30 teeth and module 2 has a 60 mm pitch diameter. Because the pitch circle is not a surface you can touch, measure the tip diameter instead: for a standard spur gear it is m (z + 2), so m = tip diameter ÷ (teeth + 2). A 30-tooth gear with a 64 mm tip diameter is module 2.
The tooth proportions come from the ISO 53 basic rack (profile A, the default for general engineering): pressure angle 20°, addendum 1.00 m above the pitch line, dedendum 1.25 m below it. The extra 0.25 m is the bottom clearance that keeps the tip of one gear from touching the root of the other. Tooth thickness and space width on the pitch line are each half the circular pitch, πm/2.
In the chart, p is the circular pitch (tooth-to-tooth distance along the pitch circle), ha the addendum, hf the dedendum and h the whole depth. The DP columns convert to the inch system: diametral pitch DP = 25.4 / m. No module equals a standard DP exactly, so the nearest DP gear is close but not interchangeable: a module 2.5 gear (DP 10.16) will not run properly with a 10 DP gear.
About Gear Modules
Metric gears are specified by module, inch gears by diametral pitch. Both describe tooth size, but inversely: a larger module means a larger tooth, a larger DP a smaller one. ISO 54 lists the modules from 1 to 50 mm in two series. Use series I (1, 1.25, 1.5, 2, 2.5, 3, 4, 5, 6, 8, 10 …) wherever you can; series II values (1.125, 1.375, 1.75, 2.25 …) are second choice. Stock gears, racks and gear cutters are made mostly in series I sizes.
Below module 1, ISO 54 does not apply. DIN 780-1 and JIS B 1701-2 list fine modules such as 0.3, 0.4, 0.5, 0.6, 0.7, 0.75, 0.8 and 0.9; module 0.5 and 0.8 are typical for small plastic gears, servos and instruments. Older German series also contain 3.25, 3.75 and 6.5; avoid them in new designs.
The dimensions in this chart are those of the basic rack. Real gears may have a profile shift (to avoid undercut or to set a centre distance), tip relief or a different dedendum (1.25 m is the ISO 53 default; 1.2 m, 1.3 m and 1.4 m occur). The module and pressure angle are what must match for two gears to mesh.
Choosing a module
Tooth bending strength grows roughly with the square of the module for the same face width ratio, while noise and size grow with it too. A quick start: estimate the pitch diameter from the space and torque, pick a tooth count of 17 or more for the pinion (to avoid undercut at 20°), and take the nearest series I module. Check the result with a strength calculation (ISO 6336 or AGMA 2101).
Module, diametral pitch and circular pitch
Three ways to say the same thing: module m (mm of pitch diameter per tooth), diametral pitch DP (teeth per inch of pitch diameter, DP = 25.4 / m) and circular pitch p (distance between teeth along the pitch circle, p = πm). Some inch gears and most roller chains are specified by circular pitch. CP 1/2 in equals module 4.04, which is not a standard module either.
Pressure angle
20° is the standard for metric gears and almost all modern inch gears. 14.5° appears on older inch gears and some replacement parts, 25° on some high-load gears. Gears with different pressure angles do not mesh correctly even when the module is the same.
Questions
How do I find the module of a gear?
Count the teeth and measure the outside (tip) diameter. For a standard spur gear, module = tip diameter ÷ (teeth + 2). Example: 40 teeth and 84 mm outside diameter → 84 / 42 = module 2. If the result is not close to a standard module, the gear may be an inch (DP) gear: DP = (teeth + 2) ÷ tip diameter in inches.
How do I convert module to diametral pitch?
DP = 25.4 / m, and m = 25.4 / DP. Module 2 equals 12.7 DP; 10 DP equals module 2.54. Because the results are not standard values, metric and inch gears are not interchangeable even when they look alike.
What is the tooth depth of a module 2 gear?
With the ISO 53 basic rack, whole depth = 2.25 × m = 4.5 mm: addendum 2 mm above the pitch circle and dedendum 2.5 mm below it.
How do I calculate the centre distance of two gears?
For standard spur gears without profile shift, a = m (z1 + z2) / 2. Two module 2 gears with 20 and 40 teeth sit 60 mm apart. Allow a small positive tolerance for backlash.
What is the circular pitch of module 1?
p = π × m = 3.1416 mm. The tooth thickness on the pitch circle is half of that, 1.5708 mm.
What is the minimum number of teeth for a spur gear?
With a 20° pressure angle, the theoretical limit without undercut is 17 teeth (2 / sin²20° = 17.1); about 14 teeth is acceptable in practice. Fewer teeth need a positive profile shift.
Sources
- ISO 54:1996, Cylindrical gears for general engineering and for heavy engineering: Modules
- ISO 53:1998, Cylindrical gears for general and heavy engineering: Standard basic rack tooth profile
- DIN 780-1: Series of modules for gears (modules below 1 mm)
- KHK Gear Technical Reference: Module sizes and tooth profile
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.