Blind Rivet Sizes and Drill Sizes (Pop Rivets)
A blind rivet is set from one side: the tool pulls the mandrel, which swells the tail behind the sheets and snaps off. The hole is 0.1 mm larger than the rivet: a 3.2 mm (1/8 in) rivet goes in a 3.3 mm hole or a #30 drill (0.1285 in).
Size chartTap a size for its drawing and full specs
| Rivet ⌀ | dDiametermmin | d3Recommended holemmin | dkDome head diameter (typical)mmin | Inch equivalent | Inch drill (IFI) |
|---|---|---|---|---|---|
| 2.4 mm (3/32") | 2.40.094 | 2.50.098 | 5.00.197 | 3/32 in | #41 (0.096 in) |
| 3.0 mm | 3.00.118 | 3.10.122 | 6.50.256 | — | — |
| 3.2 mm (1/8") | 3.20.126 | 3.30.130 | 6.50.256 | 1/8 in | #30 (0.1285 in) |
| 4.0 mm (5/32") | 4.00.157 | 4.10.161 | 8.00.315 | 5/32 in | #20 (0.161 in) |
| 4.8 mm (3/16") | 4.80.189 | 4.90.193 | 9.50.374 | 3/16 in | #11 (0.191 in) |
| 5.0 mm | 5.00.197 | 5.10.201 | 9.50.374 | — | — |
| 6.0 mm | 6.00.236 | 6.10.240 | 12.00.472 | — | — |
| 6.4 mm (1/4") | 6.40.252 | 6.50.256 | 13.00.512 | 1/4 in | F (0.257 in) |
No exact match. The nearest sizes:
How to choose a blind rivet
Diameter: pick by load and sheet thickness: 3.2 mm (1/8 in) and 4.0 mm (5/32 in) for general sheet metal, 4.8 mm (3/16 in) for heavier work. Hole: drill to the value in the chart (d + 0.1 mm); a loose hole reduces strength and lets the rivet tilt.
Length comes from the grip range, the total thickness of the parts being joined. Each rivet length covers a grip range printed by the maker; ranges for the same length differ between brands, so use the maker’s table. In inch sizes the length is the dash number: IFI rivets are coded diameter in 1/32 in and maximum grip in 1/16 in. An AD 4-4 is 4/32 = 1/8 in diameter for grips up to 4/16 = 1/4 in.
Material: match the rivet to the sheets to avoid galvanic corrosion: aluminium rivets with steel mandrel for aluminium, steel for steel, stainless for stainless. Aluminium/steel rivets in stainless sheet corrode quickly outdoors.
About Blind Rivets
This chart covers the common open-end dome head rivet (DIN 7337 form A, now the ISO 15977 to 15984 series by material). Large flange heads (about 3 × d) spread the load on soft materials; countersunk heads sit flush in a 120° countersink.
Head diameters are typical values: makers differ by a few tenths, especially between aluminium, steel and stainless rivets. The head height of the dome is roughly 0.8 mm for 3.2 mm rivets and 1.1 mm for 4.8 mm rivets.
Closed-end (sealed) rivets keep water and dust out; multi-grip rivets cover a wider grip range with one length; structural rivets (lockbolt-type) lock the mandrel in place and carry much higher shear loads.
Questions
What size drill for a 1/8 pop rivet?
A #30 drill (0.1285 in, 3.26 mm). In metric, use 3.3 mm. A plain 1/8 in drill is usually too tight.
What size drill for a 3/16 rivet?
#11 (0.191 in) or 4.9 mm.
How do I choose the rivet length?
Add up the thickness of all sheets (the grip) and choose a rivet whose grip range includes it. Too long and the tail does not form tightly; too short and it does not form at all.
What does AD44 mean on a rivet?
A = aluminium rivet, D = dome head, 4 = 4/32 in (1/8 in) diameter, 4 = maximum grip 4/16 in (1/4 in).
Sources
- DIN 7337: Blind rivets with break pull mandrel (superseded by the ISO 15977–15984 series)
- IFI-114: Break mandrel blind rivets (inch)
- Westfield Fasteners: DIN 7337 blind rivets, joint hole table
- Timco: Rivets technical data sheet
- Rivelit: Standard blind rivets DIN 7337 catalogue
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.