Audio Jack Sizes and Pinouts: 3.5 mm, 6.35 mm, 2.5 mm, 4.4 mm, XLR

Phone plugs come in three common diameters, 2.5 mm, 3.5 mm and 6.35 mm (1/4 in), plus the 4.4 mm balanced plug. The number of black rings tells you the wiring: TS (mono, 2 contacts), TRS (stereo or balanced, 3), TRRS (stereo + mic, 4). On a 3.5 mm headset plug the order is tip left, ring right, then ground and mic (CTIA).

13 connectorsChecked 2026-11-156 sources

Connector chartTap a connector for its pinout and drawing

13 of 13
ConnectordPlug diametermminContactsSignalTypical use
Phone plugs (jacks)
6.35 mm (1/4 in) TS6.350.2502Unbalanced monoGuitar and instrument cables, unbalanced line, older passive speakers
6.35 mm (1/4 in) TRS6.350.2503Stereo or balanced monoStudio headphones, balanced line (mixers, monitors), insert cables
3.5 mm TS3.50.1382Unbalanced monoMono earpieces, some line and trigger connections
3.5 mm TRS3.50.1383Unbalanced stereoHeadphones, aux cables, line out, PC audio
3.5 mm TRRS (CTIA)3.50.1384Stereo + microphoneHeadsets for iPhone, Android, laptops, consoles (current standard)
3.5 mm TRRS (OMTP)3.50.1384Stereo + microphoneOlder Nokia, Sony Ericsson and some other phones
2.5 mm TRS2.50.0983Unbalanced stereoOlder phones and walkie-talkies, some headphone cables, camera remotes
2.5 mm TRRS (balanced)2.50.0984Balanced stereoBalanced headphone outputs on portable players (Astell&Kern and others)
4.4 mm Pentaconn (TRRRS)4.40.1735Balanced stereoBalanced headphones on players and DACs (Sony, FiiO and others)
XLR
XLR 3-pin—3Balanced monoMicrophones, balanced line, DMX lighting (5-pin is the DMX standard)
XLR 4-pin (headphone)—4Balanced stereoBalanced headphones and headphone amplifiers; also 12 V power on cameras and intercoms
RCA and Speakon
RCA (phono)—2Unbalanced mono (one per channel)Hi-fi line level, turntables, composite video, S/PDIF coaxial
Speakon NL4—4Speaker level, 1 or 2 channelsProfessional loudspeakers and amplifiers (locking, high current)

Tip, ring, sleeve

A phone plug is named after its contacts, counted from the end: Tip, Ring(s), Sleeve. The thin insulating bands between them are what you count: one band = TS, two = TRS, three = TRRS, four = TRRRS (the 4.4 mm balanced plug).

The same TRS plug can carry two different signals. Headphones use it for stereo (tip left, ring right, sleeve ground). Studio gear uses it for balanced mono (tip hot, ring cold, sleeve shield), which rejects hum over long cables. Plugging stereo headphones into a balanced output works but sounds wrong; check what the socket is for.

Measure the plug shaft with calipers: about 2.5, 3.5, 4.4 or 6.3 mm. The 1/4 in plug is 6.35 mm nominal (often listed as 6.3 mm). Two look-alikes are not interchangeable: Bantam / TT patch-bay plugs are 0.173 in (4.4 mm), the same diameter as the 4.4 mm balanced plug but a different shape, and aviation microphone plugs are 0.206 in (5.2 mm).

About Audio Jacks & Connectors

CTIA vs OMTP: both are 3.5 mm TRRS with left and right on the tip and first ring. CTIA (also called AHJ) puts ground on the second ring and the microphone on the sleeve; OMTP swaps them. Almost every phone, laptop and console sold today uses CTIA. An OMTP headset in a CTIA socket (or the reverse) gives very quiet, hollow sound that returns to normal while you hold the button, because the mic and ground are crossed; a short swap adapter fixes it.

Balanced headphone connectors keep each driver's return separate: 2.5 mm TRRS (portable players), 4.4 mm Pentaconn (now the most common balanced plug on players and DACs, with an extra ground contact) and 4-pin XLR (desktop amplifiers). A balanced plug cannot go into a normal 3.5 mm or 6.35 mm socket; adapters must be wired for it.

XLR carries balanced microphone and line signals. The standard assignment is pin 1 shield, pin 2 hot, pin 3 cold; the pins are numbered on the connector face. RCA is unbalanced, one plug per channel (red right, white or black left; yellow composite video). Speakon is a locking speaker connector for amplifier outputs; it is rated for high current and cannot be confused with signal cables.

Which headset fits which socket

PlugInto a CTIA headset socketInto a plain 3-contact headphone socket
TRS headphones (stereo)Works, no micWorks
TRRS CTIA headsetWorks with micWorks as headphones in most sockets
TRRS OMTP headsetHollow sound, mic not working (needs swap adapter)Mostly works as headphones
TS mono plugSound on one side only (or shorted right channel)Left side only

Colour codes

PC sound cards (PC 99 colour code): green line out (front speakers / headphones), pink microphone, light blue line in; black, orange and grey are surround outputs. RCA: red right audio, white or black left audio, yellow composite video, orange coaxial S/PDIF (digital audio).

Questions

What is the difference between CTIA and OMTP?

The position of ground and microphone on a 3.5 mm TRRS plug. CTIA: tip left, ring 1 right, ring 2 ground, sleeve mic. OMTP: tip left, ring 1 right, ring 2 mic, sleeve ground. Current phones and laptops use CTIA.

Is 1/4 inch the same as 6.35 mm?

Yes. 1/4 in = 6.35 mm; the plug is often called 6.3 mm in Europe. It is not the same as the 0.173 in (4.4 mm) Bantam/TT patch-bay plug or the 0.206 in (5.2 mm) aviation microphone plug.

What does TRS mean?

Tip, Ring, Sleeve: a plug with three contacts, used for stereo headphones (left, right, ground) or balanced mono audio (hot, cold, shield). TS has two contacts (mono), TRRS four.

What is the XLR pinout?

Pin 1 shield/ground, pin 2 hot (+), pin 3 cold (−), per IEC 60268-12 and AES14. The pin numbers are moulded into the connector face.

What is a 4.4 mm balanced jack?

A 5-contact (TRRRS) plug, 4.4 mm in diameter, standardized as JEITA RC-8141C (Pentaconn): tip L+, ring 1 L−, ring 2 R+, ring 3 R−, sleeve ground. It is used for balanced headphone outputs.

Sources

  1. EIA RS-453 / IEC 60603-11: concentric phone plugs (0.206 in type); MIL-DTL-642 telephone plugs
  2. JEITA RC-8141C: 4.4 mm 5-pole (Pentaconn) headphone plug; Nippon DICS Pentaconn product data
  3. IEC 60268-12 / AES14: Application of connectors for broadcast and audio (XLR pin 1 shield, 2 hot, 3 cold)
  4. Neutrik: XLR and speakON (NL2, NL4) connector data sheets and wiring
  5. Switchcraft: 1/4 in and 3.5 mm phone plug drawings
  6. Wikipedia: Phone connector (audio): CTIA vs OMTP TRRS, balanced conventions

Values last checked against these sources on November 15, 2026. · How we check data

Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.