Helicoil Thread Insert Sizes: STI Tap Drill and Insert Lengths
A wire thread insert repairs a stripped thread or gives a strong steel thread in aluminium, magnesium or plastic. Drill with the STI tap drill (6.3 mm for M6), tap with the STI tap of the same thread, and wind in an insert of length 1d to 3d. After installation the hole takes a standard M6 screw.
Size chartTap a size for its drawing and full specs
| Thread | PPitchmmin | ⌀Tap drill for STI tap (typical)mmin | 1dInsert length 1dmmin | 1.5dInsert length 1.5dmmin | 2dInsert length 2dmmin | 2.5dInsert length 2.5dmmin | 3dInsert length 3dmmin |
|---|---|---|---|---|---|---|---|
| M2 | 0.40.0157 | 2.10.0827 | 20.079 | 30.118 | 40.157 | 50.197 | 60.236 |
| M2.5 | 0.450.0177 | 2.60.1024 | 2.50.098 | 3.80.148 | 50.197 | 6.30.246 | 7.50.295 |
| M3 | 0.50.0197 | 3.20.1260 | 30.118 | 4.50.177 | 60.236 | 7.50.295 | 90.354 |
| M4 | 0.70.0276 | 4.20.1654 | 40.157 | 60.236 | 80.315 | 100.394 | 120.472 |
| M5 | 0.80.0315 | 5.20.2047 | 50.197 | 7.50.295 | 100.394 | 12.50.492 | 150.591 |
| M6 | 10.0394 | 6.30.2480 | 60.236 | 90.354 | 120.472 | 150.591 | 180.709 |
| M8 | 1.250.0492 | 8.40.3307 | 80.315 | 120.472 | 160.630 | 200.787 | 240.945 |
| M10 | 1.50.0591 | 10.50.4134 | 100.394 | 150.591 | 200.787 | 250.984 | 301.181 |
| M12 | 1.750.0689 | 12.50.4921 | 120.472 | 180.709 | 240.945 | 301.181 | 361.417 |
| M14 | 20.0787 | 14.50.5709 | 140.551 | 210.827 | 281.102 | 351.378 | 421.654 |
| M16 | 20.0787 | 16.50.6496 | 160.630 | 240.945 | 321.260 | 401.575 | 481.890 |
| M20 | 2.50.0984 | 20.750.8169 | 200.787 | 301.181 | 401.575 | 501.969 | 602.362 |
| M24 | 30.1181 | 250.9843 | 240.945 | 361.417 | 481.890 | 602.362 | 722.835 |
No exact match. The nearest sizes:
How to install a wire thread insert
1. Drill with the tap drill in the chart, to the insert length plus at least 1 to 2 thread pitches for a blind hole. 2. Countersink lightly (90° or 120°) so the first coil seats. 3. Tap with the STI tap (marked e.g. EG M6 or STI M6×1). An ordinary M6 tap cuts a hole far too small. 4. Wind in the insert with the installation tool until the top coil is ¼ to ½ turn below the surface. 5. Break off the tang on through-hole and tanged inserts with the tang breaker.
The STI tap has the same pitch as the final thread but a larger diameter, sized so that the insert's diamond-shaped wire fills the space between the STI thread and the screw thread. Tap drills differ by up to 0.1 mm between insert makers and between aluminium and steel (M8: 8.3–8.4 mm, M10: 10.4–10.5 mm, M12: 12.4–12.5 mm); the chart gives the common value, but follow the drill size printed on your kit.
Insert length: 1d to 1.5d in steel and cast iron, 1.5d to 2d in aluminium, 2d to 3d in magnesium and soft materials. The insert length is its nominal length after installation.
About Thread Inserts
Helical wire inserts are made of stainless steel (or phosphor bronze) diamond-section wire wound into a coil. The standard types are free-running and screw-locking (one or more polygonal coils grip the screw). Tanged inserts have a drive tang that is broken off after installation; tangless inserts are driven by a notch and need no tang removal.
Besides repairs, inserts are designed into new parts: a steel thread in aluminium resists wear and stripping much better than the parent material, and the flexible coil spreads the load over all engaged threads.
Inch versions for UNC/UNF threads use the same principle with their own STI taps and drills (for example 17/64 in for 1/4-20). This chart covers ISO metric coarse threads.
Questions
What drill size for an M8 helicoil?
8.4 mm for the M8 × 1.25 STI tap (typical; follow the size on the kit).
What drill size for an M6 helicoil?
6.3 mm, then tap with the M6 STI tap. Insert lengths are 6, 9, 12, 15 and 18 mm (1d to 3d).
Can I use a normal tap for a helicoil?
No. The insert needs the oversize STI thread. A normal tap leaves too little room and the insert will not go in.
How long should the insert be?
1.5d is the usual choice in aluminium; 1d is enough in steel; use 2d or more in magnesium, plastic or when the screw is high-strength.
Sources
- DIN 8140-1 / ISO 13431: Wire thread inserts for ISO metric screw threads
- Böllhoff: HELICOIL thread inserts, technical catalogue (STI tap drills, nominal lengths)
- Albany County Fasteners: HeliCoil thread repair sizing chart
- AmesWeb: Helicoil tap sizes (STI)
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.