Bottle Neck Finish Chart: 400, 410, 415 and PCO Threads
A neck finish such as 28-400 names the thread outside diameter in millimetres (28) and the thread style (400 = one full turn). The real thread diameter T sits just under the name: a 28-400 neck measures 1.068–1.088 in (27.1–27.6 mm) across the crests and has 6 threads per inch. Cap and bottle must match in both numbers.
Size chartTap a size for its drawing and full specs
| Finish | TThread OD (T)mminmm · in | HFinish height (H)mminmm · in | STop to thread (S)mminmm · in | IBore, min (I)mminmm · in | Threads per inch | PPitchmminmm · in | Thread turns | HFinish heightmminmm · in | Starts | Neck weight (about)g |
|---|---|---|---|---|---|---|---|---|---|---|
| 400 series (one turn, shallow) | ||||||||||
| 18-400 | 17.48–17.880.688–0.704 | 9.04–9.800.356–0.386 | 0.56–1.320.022–0.052 | 8.260.325 | 8 | 3.180.125 | 1 (360°) | — | 1 | — |
| 20-400 | 19.48–19.890.767–0.783 | 9.04–9.800.356–0.386 | 0.56–1.320.022–0.052 | 10.260.404 | 8 | 3.180.125 | 1 (360°) | — | 1 | — |
| 24-400 | 23.47–23.880.924–0.940 | 9.78–10.540.385–0.415 | 0.79–1.550.031–0.061 | 13.110.516 | 8 | 3.180.125 | 1 (360°) | — | 1 | — |
| 28-400 | 27.13–27.641.068–1.088 | 9.78–10.540.385–0.415 | 0.79–1.550.031–0.061 | 15.600.614 | 6 | 4.230.167 | 1 (360°) | — | 1 | — |
| 38-400 | 36.88–37.491.452–1.476 | 9.86–10.620.388–0.418 | 0.79–1.550.031–0.061 | 25.070.987 | 6 | 4.230.167 | 1 (360°) | — | 1 | — |
| 53-400 | 51.61–52.502.032–2.067 | 9.98–10.740.393–0.423 | 0.79–1.550.031–0.061 | 40.081.578 | 6 | 4.230.167 | 1 (360°) | — | 1 | — |
| 63-400 | 61.62–62.512.426–2.461 | 9.98–10.740.393–0.423 | 0.79–1.550.031–0.061 | 50.091.972 | 6 | 4.230.167 | 1 (360°) | — | 1 | — |
| 70-400 | 68.61–69.492.701–2.736 | 9.98–10.740.393–0.423 | 0.79–1.550.031–0.061 | 57.072.247 | 6 | 4.230.167 | 1 (360°) | — | 1 | — |
| 89-400 | 88.29–89.183.476–3.511 | 13.21–13.970.520–0.550 | 1.14–1.900.045–0.075 | 74.122.918 | 5 | 5.080.200 | 1 (360°) | — | 1 | — |
| 410 series (1.5 turns, taller) | ||||||||||
| 18-410 | 17.48–17.880.688–0.704 | 12.90–13.670.508–0.538 | 0.56–1.320.022–0.052 | 8.260.325 | 8 | 3.180.125 | 1.5 (540°) | — | 1 | — |
| 20-410 | 19.48–19.890.767–0.783 | 13.69–14.450.539–0.569 | 0.56–1.320.022–0.052 | 10.260.404 | 8 | 3.180.125 | 1.5 (540°) | — | 1 | — |
| 24-410 | 23.47–23.880.924–0.940 | 16.03–16.790.631–0.661 | 0.79–1.550.031–0.061 | 13.110.516 | 8 | 3.180.125 | 1.5 (540°) | — | 1 | — |
| 28-410 | 27.13–27.641.068–1.088 | 17.60–18.360.693–0.723 | 0.79–1.550.031–0.061 | 15.600.614 | 6 | 4.230.167 | 1.5 (540°) | — | 1 | — |
| 415 series (2 turns, tallest) | ||||||||||
| 18-415 | 17.48–17.880.688–0.704 | 15.29–16.050.602–0.632 | 0.56–1.320.022–0.052 | 8.260.325 | 8 | 3.180.125 | 2 (720°) | — | 1 | — |
| 20-415 | 19.48–19.890.767–0.783 | 18.47–19.230.727–0.757 | 0.56–1.320.022–0.052 | 10.260.404 | 8 | 3.180.125 | 2 (720°) | — | 1 | — |
| 24-415 | 23.47–23.880.924–0.940 | 23.93–24.690.942–0.972 | 0.79–1.550.031–0.061 | 13.110.516 | 8 | 3.180.125 | 2 (720°) | — | 1 | — |
| 28-415 | 27.13–27.641.068–1.088 | 27.10–27.861.067–1.097 | 0.79–1.550.031–0.061 | 15.600.614 | 6 | 4.230.167 | 2 (720°) | — | 1 | — |
| PET beverage necks (PCO, 3-start) | ||||||||||
| PCO 1881 | — | — | — | — | — | 2.700.106 | 1.8 (650°) | 170.669 | 1 | 3.8 |
| PCO 1810 | — | — | — | — | — | 3.180.125 | — | 210.827 | 1 | — |
| 38 mm 3-start | — | — | — | — | — | — | — | 16.50.650 | 3 | — |
No exact match. The nearest sizes:
How to read and measure a neck finish
The two numbers. In 24-410 the first number is the nominal thread diameter in mm, the second the finish style from the SPI/GPI tables. 400 has one turn of thread (360°) on a short neck, 410 has 1.5 turns (540°) on a taller neck, 415 has 2 turns (720°) on the tallest. For one diameter, all three styles share the same T, thread pitch and S; only the height H differs.
T is the outside diameter across the thread crests. H runs from the top of the neck down to where the T diameter meets the shoulder. S is the distance from the top to the start of the first thread. I is the bore, given as a minimum so filling tubes and inserts fit.
Measuring. Put calipers across the thread crests: that is T. Pick the finish whose T range contains your reading: 23.5–23.9 mm is a 24, 27.1–27.6 mm a 28. Then count the turns of thread from start to end (one, one and a half, two) to get 400, 410 or 415, or measure H and compare it with the chart.
Tolerances. The chart gives the SPI max/min limits in inches, the unit of the tables. The mm/in switch converts them. Glass finishes under GPI drawings use the same names with slightly different limits.
About Bottle Cap Threads
Standard plastic and glass bottles and jars with screw caps are specified with these SPI/GPI continuous-thread finishes. A closure maker lists caps by the same designation, so a 24-410 pump sprayer screws onto any 24-410 bottle. The pitch is coarse and given in threads per inch: 8 TPI (3.18 mm) for 18–24 mm, 6 TPI (4.23 mm) for 28–70 mm and 5 TPI (5.08 mm) for 89 mm.
Diameter and style both matter. A 24-400 and a 24-410 have the same thread, so the cap engages, but the necks differ in height: H is 0.385–0.415 in on the 400 and 0.631–0.661 in on the 410. A 400 cap on a 410 neck seals on the lip and leaves the lower thread showing; a 410 cap on a 400 neck has a skirt longer than the neck and can bottom out on the shoulder before the liner seals.
Carbonated drinks use their own finishes. PET soda and water bottles carry the ISBT PCO 1881 neck (28 mm, 17 mm high, 2.7 mm pitch, neck about 3.8 g), which replaced the taller PCO 1810 (21 mm high, 3.18 mm pitch). Juice, dairy and still water often use a 38 mm three-start neck (EN 16068, CETIE GME 30.25). These are metric drawings, not SPI 28-400 or 38-400, and their caps do not cross over.
Pitch by diameter (SPI/GPI)
Threads per inch from the SPI tables; pitch = 25.4 mm ÷ TPI. The same pitch applies to 400, 410 and 415 of one diameter.
| Finish diameter | Threads per inch | Pitch |
|---|---|---|
| 18, 20, 24 mm | 8 | 3.18 mm |
| 28, 38, 53, 63, 70 mm | 6 | 4.23 mm |
| 89 mm | 5 | 5.08 mm |
PCO 1881 and PCO 1810
Both are 28 mm necks for carbonated drinks. The ISBT published PCO 1881 as a voluntary guideline after joint industry work from 2007 to 2009, to save material: the finish is 17 mm high instead of 21 mm. The thread is interrupted by vent slots so gas escapes before the cap comes off.
The pitches differ (2.7 mm on PCO 1881, 3.18 mm on PCO 1810), so a cap is specified for one neck only. Check the neck height: about 17 mm from the top to the support ring is 1881, about 21 mm is 1810.
Questions
What does 28-400 mean?
28 is the nominal thread diameter in mm, 400 the SPI/GPI style with one turn of thread. The measured thread diameter T is 1.068–1.088 in (27.1–27.6 mm), the height H 0.385–0.415 in, with 6 threads per inch.
Will a 24-410 cap fit a 24-400 bottle?
The thread is the same (T 0.924–0.940 in, 8 TPI), so it screws on, but the 410 cap is made for a neck 0.631–0.661 in high and the 400 neck is only 0.385–0.415 in. The skirt can hit the shoulder before the liner seals. Match both numbers.
How do I find my bottle's neck size?
Measure across the thread crests with calipers and pick the nearest T range: 17.5–17.9 mm is 18, 23.5–23.9 mm is 24, 27.1–27.6 mm is 28, 36.9–37.5 mm is 38. Then count the thread turns: one is 400, one and a half 410, two 415.
What thread is on a soda bottle?
Almost all PET soft drink and water bottles use PCO 1881: 28 mm, 17 mm finish height, 2.7 mm pitch. Older bottles use PCO 1810, 21 mm high with a 3.18 mm pitch. Neither is the same as a 28-400 finish.
What is the difference between 410 and 415?
The thread diameter and pitch are the same; 415 is taller with two turns of thread instead of 1.5. On a 24 mm finish H is 0.631–0.661 in for 410 and 0.942–0.972 in for 415.
Sources
- CKS Packaging: S.P.I. Specifications (T, H 400/410/415, S, I, threads per inch, max/min in inches)
- BOSL2 OpenSCAD library, bottlecaps.scad: SPI thread table (from ISBT thread specs) and PCO 1810/1881 neck geometry
- 3plastics: Plastic bottle cap threads specifications (T with tolerances): cross-check
- Multidesign: Neck finishes glossary (400 series S, pitch, H, I; PCO and 38 mm three-start): cross-check
- Contapack: Selected SPI neck finish specifications (mm): cross-check
- Wikipedia: Plastic bottle, PCO 1881 (17 mm finish height, 3.8 g neck, ISBT voluntary guideline)
- ISBT Threadspecs (PCO 1881 drawing 3784253-21)
- CETIE: Finish data sheets (GME 30.25, 38 mm three-start, 16.50 mm height)
- PETmolder: What is PCO 1881 neck finish (neck weight 3.8 g): cross-check
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.