G7/h6 Fit Tolerances
ISO Fits · Shaft-basis fits (h shaft)
G7/h6: Clearance fit, Shaft-basis fits (h shaft). At ⌀25 mm the hole is +28 / +7 µm, the shaft 0 / −13 µm, giving a maximum clearance of 41 µm and a minimum clearance of 7 µm (negative = interference). The table below lists the limits for every ISO size range up to 500 mm.
- Fit type
- Clearance
- Max. clearance at ⌀25 mm
- 41 µm0.00161 in0.00161 in41 µm
- Min. clearance at ⌀25 mm (− = interference)
- 7 µm0.00028 in0.00028 in7 µm
Drawing
G7/h6 specifications
| Fit type | Clearance |
|---|---|
| Hole limits at ⌀25 mm (µm) | +28 / +7 |
| Shaft limits at ⌀25 mm (µm) | 0 / −13 |
| Max. clearance at ⌀25 mm | 41 µm0.00161 in |
| Min. clearance at ⌀25 mm (− = interference) | 7 µm0.00028 in |
G7/h6 limits for every size range (µm)
| Size (mm) | Hole ES / EI | Shaft es / ei | Max. clearance | Min. clearance | Type |
|---|---|---|---|---|---|
| ≤ 3 | +12 / +2 | 0 / −6 | +18 | +2 | clearance |
| 3–6 | +16 / +4 | 0 / −8 | +24 | +4 | clearance |
| 6–10 | +20 / +5 | 0 / −9 | +29 | +5 | clearance |
| 10–18 | +24 / +6 | 0 / −11 | +35 | +6 | clearance |
| 18–30 | +28 / +7 | 0 / −13 | +41 | +7 | clearance |
| 30–50 | +34 / +9 | 0 / −16 | +50 | +9 | clearance |
| 50–80 | +40 / +10 | 0 / −19 | +59 | +10 | clearance |
| 80–120 | +47 / +12 | 0 / −22 | +69 | +12 | clearance |
| 120–180 | +54 / +14 | 0 / −25 | +79 | +14 | clearance |
| 180–250 | +61 / +15 | 0 / −29 | +90 | +15 | clearance |
| 250–315 | +69 / +17 | 0 / −32 | +101 | +17 | clearance |
| 315–400 | +75 / +18 | 0 / −36 | +111 | +18 | clearance |
| 400–500 | +83 / +20 | 0 / −40 | +123 | +20 | clearance |
Shaft-basis sliding fit, equivalent to H7/g6 with the clearance in the hole. Typical for dowel pins (m6/h6) and ground shafts carrying sliding parts.
Other fits of the same type (Clearance)
H11/c11Clearance · 370 µm · 110 µmH9/d9Clearance · 169 µm · 65 µmH9/e9Clearance · 144 µm · 40 µmH8/f7Clearance · 74 µm · 20 µmH7/f7Clearance · 62 µm · 20 µmH7/g6Clearance · 41 µm · 7 µmH7/h6Clearance · 34 µm · 0 µmH8/h7Clearance · 54 µm · 0 µmH11/h11Clearance · 260 µm · 0 µmC11/h11Clearance · 370 µm · 110 µmD9/h9Clearance · 169 µm · 65 µmF8/h7Clearance · 74 µm · 20 µm
All ISO fits
Sources
- ISO 286-1:2010, Geometrical product specifications (GPS): ISO code system for tolerances on linear sizes, Part 1: Basis of tolerances, deviations and fits
- ISO 286-2:2010, Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
- ANSI B4.2-1978 (R2020): Preferred metric limits and fits
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.