Steel Grade Equivalents: AISI, EN, W.Nr, JIS, KS, GB

The same steel carries a different name in every standard system: AISI 304 is EN X5CrNi18-10 (1.4301), JIS SUS304, KS STS304 and GB 06Cr19Ni10. Equivalents are close, not identical. Composition limits differ slightly, so a drawing that names one standard must be supplied to that standard.

36 gradesChecked 2026-11-1510 sources
1015202505101520Chromium, %Nickel, %316 / 316L310S220517-4PH410420416430 / 440C304L321304303
Each rectangle spans a grade's specified Cr and Ni range (AISI/SAE). Ferritic and martensitic grades sit at the bottom, austenitic grades higher up, duplex 2205 in between.Proportions shown, not to scale

Size chartTap a size for its drawing and full specs

36 of 36
GradeEN nameEN number (W.Nr)JISKSGB (China)C %Cr %Ni %Mo %
Carbon steels (SAE J403)
1010C101.0301S10CSM10C10————
1018≈C15≈1.0401≈S15C≈SM15C≈15————
1020C221.0402S20CSM20C20————
1035C351.0501S35CSM35C35————
1045C451.0503S45CSM45C45————
1050C501.0540S50CSM50C50————
12L1411SMnPb301.0718SUM24LSUM24L—————
Alloy and bearing steels (SAE J404, ASTM A295)
413025CrMo41.7218SCM430SCM43030CrMo0.28–0.330.80–1.10—0.15–0.25
414042CrMo41.7225SCM440SCM44042CrMo0.38–0.430.80–1.10—0.15–0.25
4340≈34CrNiMo6≈1.6582SNCM439SNCM43940CrNiMoA0.38–0.430.70–0.901.65–2.000.20–0.30
862020NiCrMo2-21.6523SNCM220SNCM22020CrNiMo————
52100100Cr61.3505SUJ2STB2GCr15————
Structural steels (EN 10025-2, ASTM)
S235JRS235JR1.0038≈SS400—Q235B≤ 0.17———
S275JRS275JR1.0044≈SS400——≤ 0.21———
S355J2S355J21.0577≈SM490B≈SM355B≈Q355D≤ 0.20———
A36≈S235JR / S275JR—≈SS400—≈Q235B≤ 0.25–0.29———
A572 Grade 50≈S355JR—≈SM490A≈SM355A≈Q355B————
Stainless steels (AISI/SAE, EN 10088)
303X8CrNiS18-91.4305SUS303STS303—≤ 0.1517.0–19.08.0–10.0—
304X5CrNi18-101.4301SUS304STS30406Cr19Ni10≤ 0.0818.0–20.08.0–10.5—
304LX2CrNi18-91.4307SUS304LSTS304L022Cr19Ni10≤ 0.03018.0–20.08.0–12.0—
310SX8CrNi25-211.4845SUS310SSTS310S06Cr25Ni20≤ 0.0824.0–26.019.0–22.0—
316X5CrNiMo17-12-21.4401SUS316STS31606Cr17Ni12Mo2≤ 0.0816.0–18.010.0–14.02.00–3.00
316LX2CrNiMo17-12-21.4404SUS316LSTS316L022Cr17Ni12Mo2≤ 0.03016.0–18.010.0–14.02.00–3.00
321X6CrNiTi18-101.4541SUS321STS32106Cr18Ni11Ti≤ 0.0817.0–19.09.0–12.0—
410X12Cr131.4006SUS410STS41012Cr13≤ 0.1511.5–13.5≤ 0.75—
416X12CrS131.4005SUS416STS416Y12Cr13≤ 0.1512.0–14.0——
420X20Cr131.4021SUS420J1STS420J120Cr13≥ 0.1512.0–14.0——
430X6Cr171.4016SUS430STS43010Cr17≤ 0.1216.0–18.0≤ 0.75—
440CX105CrMo171.4125SUS440CSTS440C—0.95–1.2016.0–18.0—≤ 0.75
2205X2CrNiMoN22-5-31.4462SUS329J3LSTS329J3L—≤ 0.03021.0–23.04.5–6.52.50–3.50
17-4PHX5CrNiCuNb16-41.4542SUS630STS63005Cr17Ni4Cu4Nb≤ 0.0715.0–17.53.0–5.0—
Tool steels (ASTM A681, ISO 4957)
D2X153CrMoV121.2379≈SKD11≈STD11Cr12Mo1V11.40–1.6011.00–13.00—0.70–1.20
A2X100CrMoV51.2363SKD12STD12Cr5Mo1V————
O1100MnCrW41.2510≈SKS3≈STS3—————
H13X40CrMoV5-11.2344SKD61STD614Cr5MoSiV1————
M2HS6-5-21.3343SKH51SKH51W6Mo5Cr4V2————

How to read steel designations

AISI/SAE four digits (1045, 4140): the first two digits give the alloy family (10 plain carbon, 41 Cr-Mo, 43 Ni-Cr-Mo, 86 Ni-Cr-Mo), the last two the carbon content in hundredths of a percent, so 1045 has about 0.45 % C. An L in the middle (12L14) means leaded, free-machining.

Stainless three digits (304, 316, 410): 3xx austenitic (non-magnetic when annealed), 4xx ferritic or martensitic (magnetic). An L suffix means low carbon (≤ 0.03 %) for welding without sensitisation; S, H and Ti suffixes or 321/347 indicate other carbon limits or stabilisation.

EN names spell out the chemistry: C45 = 0.45 % C; 42CrMo4 = 0.42 % C with Cr (4/4 = 1 %) and Mo; X5CrNi18-10 = high alloy, 0.05 % C, 18 % Cr, 10 % Ni. Structural names give the yield strength: S355J2 = 355 MPa minimum, impact tested at −20 °C. The EN number (Werkstoffnummer, W.Nr) 1.4301 is the same steel in a five-digit code: 1.0xxx unalloyed, 1.2xxx tool steels, 1.3xxx high-speed and bearing steels, 1.4xxx stainless, 1.5–1.8xxx alloy steels.

JIS uses S45C (carbon), SCM440 (Cr-Mo), SUS304 (stainless), SKD11 (die steel), SKH51 (high-speed). KS (Korea) mostly mirrors JIS with its own prefixes: SM45C, STS304, STD11. GB (China) writes carbon in hundredths (45 = 0.45 % C) and in stainless in ten-thousandths (06Cr19Ni10 = 0.06 % C, 19 % Cr, 10 % Ni).

A ≈ in the table marks a near equivalent: similar use, but the chemistry or strength differs enough that you should compare the actual specifications.

About Steel Grades

Use this table to find a substitute when the steel named on a drawing is not stocked locally, or to read a foreign mill certificate. Before substituting, compare the full specification: carbon and alloy limits, sulphur for machinability, delivery condition (annealed, normalised, quenched and tempered) and, for structural steel, impact test temperature and thickness range.

The composition columns give the key alloying elements as specified ranges in weight percent, not typical analyses. Stainless ranges are the AISI/SAE ranges; the EN and ASTM A240 versions of the same grade differ by a few tenths of a percent. For example, AISI 304 has 18.0–20.0 % Cr and ≤ 0.08 % C, while EN 1.4301 and current ASTM A240 plate specify 17.5–19.5 % Cr and ≤ 0.07 % C. Most mill certificates satisfy both.

Phosphorus, sulphur and silicon limits are omitted except where they define the grade (free-machining 303, 416, 12L14). For tool steels the manganese and silicon ranges are left out where the standards and maker sheets differ.

Structural grades are bought by strength, not chemistry. The yield values are minimums for the thinnest range (up to 16 mm for EN 10025); thicker plates have lower minimum yield.

Which stainless steel for what

A rough guide; corrosion resistance depends on surface finish, chlorides, temperature and crevices.

GradeTypeTypical use
304 / 1.4301 (A2)AusteniticKitchen equipment, food processing, general indoor and outdoor use
316 / 1.4401 (A4)Austenitic + MoMarine, chemical, swimming pools, de-icing salt exposure
303 / 1.4305Austenitic, free-machiningTurned parts; poorer corrosion resistance and weldability than 304
430 / 1.4016FerriticAppliance panels, trim, indoor use; magnetic, not hardenable
410, 420 / 1.4021MartensiticHardenable: pump shafts, cutlery, surgical tools
440C / 1.4125Martensitic, high CBearings, knife blades, valve parts up to ~58–60 HRC
2205 / 1.4462DuplexHigher strength and chloride resistance than 316: offshore, tanks
17-4PH / 1.4542Precipitation hardeningHigh-strength shafts, aerospace and valve parts

Fastener stainless grades A2 and A4

Stainless bolts and nuts to ISO 3506 are marked with the steel group and property class: A2-70 is austenitic 18-8 (typically 304), A4-80 is molybdenum-alloyed austenitic (typically 316), the number giving the tensile strength in tens of MPa. A2 and A4 are not grade names in themselves; they cover several similar alloys.

Questions

What is the European equivalent of 304 stainless?

EN 1.4301 (X5CrNi18-10). The low-carbon 304L is 1.4307 (X2CrNi18-9) or 1.4306. 316 is 1.4401, 316L 1.4404.

What is the equivalent of 4140 steel?

EN 42CrMo4 (1.7225), JIS and KS SCM440, GB 42CrMo. All are Cr-Mo steels with about 0.4 % C, 1 % Cr and 0.2 % Mo.

Is SKD11 the same as D2?

Nearly. Both have 1.40–1.60 % C and 11–13 % Cr. SKD11 specifies 0.20–0.50 % V, D2 up to 1.10 % V. In practice they are used interchangeably for dies and punches; check the supplier sheet for heat treatment.

What is the US equivalent of S355?

ASTM A572 Grade 50 (345 MPa / 50 ksi minimum yield) is the usual counterpart. S235 and S275 are close to ASTM A36 (250 MPa).

What does SUS mean in SUS304?

SUS is the JIS prefix for stainless steel (Steel Use Stainless). Korea's KS uses STS for the same grades: STS304, STS316.

Sources

  1. SAE J403: Chemical compositions of SAE carbon steels; SAE J404: Chemical compositions of SAE alloy steels
  2. ASTM A240/A240M: Chromium and chromium-nickel stainless steel plate, sheet and strip
  3. Wikipedia: SAE steel grades (stainless composition table, AISI/SAE ranges)
  4. Wikipedia: 41xx steel (4130, 4140 composition)
  5. ASTM A681: Tool steels alloy
  6. EN 10088-1: Stainless steels, list of stainless steels (names and numbers)
  7. EN 10025-2:2019, Hot rolled products of structural steels, non-alloy structural steels
  8. ISO 4957:2018, Tool steels
  9. JIS G 4303 / G 4051 / G 4053 / G 4404: stainless, carbon, alloy and tool steels (JISC)
  10. GB/T 20878-2007: Stainless and heat-resisting steels, designation and chemical composition

Values last checked against these sources on November 15, 2026. · How we check data

Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.