Carriage Bolt Dimensions (DIN 603 and ASME B18.5)

A carriage bolt (coach bolt in the UK) has a low domed head and a square neck that locks into wood or a square hole, so the nut can be tightened from one side. An M8 carriage bolt (DIN 603) has a 20.65 mm head and an 8.58 mm square neck; a 1/4"-20 (ASME B18.5) has a 0.594 in head and a 0.260 in square.

15 bolt sizesChecked 2026-11-154 sources

Size chartTap a size for its drawing and full specs

15 of 15
SizedkHead diametermminmm · inkHead heightmminmm · invSquare neck width (max)mminmm · infSquare neck depth (max)mminmm · in
Metric: DIN 603 / ISO 8677
M513.550.5333.30.1305.480.2164.10.161
M616.550.6523.880.1536.480.2554.60.181
M820.650.8134.880.1928.580.3385.60.220
M1024.650.9705.380.21210.580.4176.60.260
M1230.651.2076.950.27412.70.5008.750.344
M1638.81.5288.950.35216.70.65712.90.508
M2046.81.84311.050.43520.840.82015.90.626
Inch: ASME B18.5
#10-2411.910.4692.90.1145.060.1993.180.125
1/4"-2015.090.5943.680.1456.60.2603.960.156
5/16"-1818.260.7194.470.1768.230.3244.750.187
3/8"-1621.440.8445.280.2089.860.3885.560.219
7/16"-1424.610.9696.070.23911.480.4526.350.250
1/2"-1327.791.0946.860.27013.080.5157.140.281
5/8"-1134.141.3448.740.34416.310.6428.740.344
3/4"-1040.491.59410.310.40619.510.76810.310.406

How to read the chart

dk is the head diameter, k the head height, v the width across the flats of the square neck and f its depth below the head, all maximum values. Carriage bolt length is measured from under the head (the neck counts as part of the length).

Inch rows show inches first and metric rows millimetres first; the mm/in switch at the top changes every row.

In wood, drill a round hole of the thread diameter and pull the neck in by tightening the nut; the square cuts its own seat. In steel, punch or file a square hole slightly larger than v (an M10 neck is 10.58 mm max, so an 11 mm square hole).

About Carriage Bolts

Carriage bolts are used where the head side must be smooth and tamper-resistant: timber frames, playground equipment, gates, trailer beds and shelving. The domed head offers no grip for a tool, and the square neck stops the bolt turning while the nut is tightened.

The metric standard is DIN 603; ISO 8677 is the corresponding international standard (cup head square neck bolt). DIN 603 bolts come in property class 4.6 or 8.8 and stainless A2/A4, usually zinc plated or hot-dip galvanised for outdoor wood. The inch standard ASME B18.5 covers round head square neck bolts from #10 to 1 in; Grade 2 and Grade 5 are typical.

The head is roughly 2.5 × d across for metric and 2 × d + 3/32 in for inch bolts. That large bearing area is why carriage bolts are often used in wood without a washer under the head. Always put a washer under the nut, though.

Metric vs. inch carriage bolts

An M8 and a 5/16 in carriage bolt look alike (8 mm vs. 7.94 mm), but the threads do not mix: M8 has 1.25 mm pitch, 5/16-18 has 1.41 mm. The DIN 603 head is also wider (20.65 mm vs. 18.3 mm). Check the thread with a nut before a project.

Questions

What size hole for a carriage bolt?

In wood, drill the thread diameter (8 mm for M8, 3/8 in for 3/8 in) and pull the square neck in with the nut. In metal, make a square hole slightly larger than the neck: 9 mm square for M8 (neck 8.58 mm).

What is the head diameter of an M8 carriage bolt?

20.65 mm maximum to DIN 603, with a 4.88 mm head height.

Is a coach bolt the same as a carriage bolt?

In British usage, yes: 'coach bolt' means the mushroom head square neck bolt (DIN 603). In the US a coach screw is a lag screw, a different part.

How is carriage bolt length measured?

From under the head to the end of the thread, square neck included.

Sources

  1. DIN 603:2017, Mushroom head square neck bolts
  2. ASME B18.5: Round head bolts (inch series)
  3. Böllhoff: DIN 603 steel 8.8 data sheet
  4. Aspen Fasteners: 1/4"-20 carriage bolts, ASME B18.5 dimensions

Values last checked against these sources on November 15, 2026. · How we check data

Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.