Hex Bolt and Cap Screw Sizes (Inch, ASME B18.2.1)
The head of an inch hex bolt is sized by its width across flats F, which is the wrench you need. Up to 7/16 in it is d + 3/16 in (1/4 in bolt: 7/16 in wrench); at 1/2 in and from 5/8 in up it is 1.5 × d (1/2 in bolt: 3/4 in wrench). Heavy hex bolts are one wrench size larger.
Size chartTap a size for its drawing and full specs
| Size | FWidth across flatsmmin | GWidth across cornersmmin | HHead height, cap screw (basic)mmin | Head height, hex bolt (basic)mmin | Across flats, heavy hexmmin | nCoarse thread (UNC)mmTPI | nFine thread (UNF)mmTPI |
|---|---|---|---|---|---|---|---|
| 1/4" | 11.17/16 | 12.830.505 | 3.975/32 | 4.3711/64 | — | 1.27020 | 0.90728 |
| 5/16" | 12.71/2 | 14.660.577 | 5.1613/64 | 5.567/32 | — | 1.41118 | 1.05824 |
| 3/8" | 14.39/16 | 16.510.650 | 5.9515/64 | 6.351/4 | — | 1.58816 | 1.05824 |
| 7/16" | 15.95/8 | 18.340.722 | 7.149/32 | 7.5419/64 | — | 1.81414 | 1.27020 |
| 1/2" | 19.03/4 | 22.000.866 | 7.945/16 | 8.7311/32 | 22.27/8 | 1.95413 | 1.27020 |
| 9/16" | 20.613/16 | 23.830.938 | 9.1323/64 | — | — | 2.11712 | 1.41118 |
| 5/8" | 23.815/16 | 27.511.083 | 9.9225/64 | 10.7227/64 | 27.01 1/16 | 2.30911 | 1.41118 |
| 3/4" | 28.61 1/8 | 32.991.299 | 11.9115/32 | 12.701/2 | 31.81 1/4 | 2.54010 | 1.58816 |
| 7/8" | 33.31 5/16 | 38.511.516 | 13.8935/64 | 14.6837/64 | 36.51 7/16 | 2.8229 | 1.81414 |
| 1" | 38.11 1/2 | 43.991.732 | 15.4839/64 | 17.0743/64 | 41.31 5/8 | 3.1758 | 2.11712 |
| 1-1/8" | 42.91 11/16 | 49.501.949 | 17.4611/16 | 19.053/4 | 46.01 13/16 | 3.6297 | 2.11712 |
| 1-1/4" | 47.61 7/8 | 54.992.165 | 19.8425/32 | 21.4327/32 | 50.82 | 3.6297 | 2.11712 |
| 1-3/8" | 52.42 1/16 | 60.502.382 | 21.4327/32 | 23.0229/32 | 55.62 3/16 | 4.2336 | 2.11712 |
| 1-1/2" | 57.22 1/4 | 65.992.598 | 23.8115/16 | 25.401 | 60.32 3/8 | 4.2336 | 2.11712 |
No exact match. The nearest sizes:
Hex bolt or hex cap screw?
ASME B18.2.1 distinguishes the hex cap screw (finished hex bolt) from the plain hex bolt. Both have the same width across flats F, but the cap screw has a washer face under the head, tighter tolerances and a lower head (H); the hex bolt has a slightly taller head (Hb). Grade 5 and Grade 8 'hex bolts' in hardware stores are actually hex cap screws.
F is the basic width across flats, the wrench size. G is the maximum width across corners. Heights are basic (nominal) values; actual heads are within a few thousandths. Length is measured from under the head.
A size is written diameter–threads per inch × length: 3/8"-16 × 1-1/2" is a 3/8 in coarse-thread bolt 1-1/2 in long. Grade markings on the head: 3 radial lines = Grade 5, 6 lines = Grade 8, none = Grade 2.
About Inch Hex Bolts
Inch hex bolts follow ASME B18.2.1. The table lists the regular hex head used for Grade 2, 5 and 8 bolts and the heavy hex head (from 1/2 in) used for structural bolts, A193 B7 studs-and-bolts and high-strength applications where a larger bearing surface is needed.
The wrench sizes are fractions of an inch and do not match metric wrenches well: 1/2 in (12.7 mm) sits between 12 and 13 mm, 9/16 in (14.3 mm) between 14 and 15 mm. A metric socket on an inch bolt head rounds the corners under torque.
Thread pitch is given for both series: UNC (coarse) for general use and UNF (fine) where finer adjustment, thin walls or higher tensile area matter. 1 in UNF is 12 TPI; the 14 TPI '1-14 UNS' is a special thread.
Wrench size rule of thumb
Regular hex: F = 1.5 × d from 5/8 in up (5/8 → 15/16, 3/4 → 1-1/8, 1 → 1-1/2). Heavy hex: F = 1.5 × d + 1/8 in (1/2 → 7/8, 3/4 → 1-1/4, 1 → 1-5/8). Heavy hex nuts follow the same rule, so a heavy hex bolt and its nut take the same wrench.
Questions
What size wrench for a 3/8 bolt?
9/16 in. A 1/4 in bolt takes 7/16 in, 5/16 in takes 1/2 in, 7/16 in takes 5/8 in, 1/2 in takes 3/4 in and 5/8 in takes 15/16 in.
What size socket for a 1/2 inch bolt?
3/4 in for a standard hex bolt or cap screw, 7/8 in for a heavy hex bolt.
How tall is the head of a 1/4-20 bolt?
5/32 in (0.156 in) basic for a hex cap screw, 11/64 in (0.172 in) for an unfinished hex bolt.
What is the difference between a hex bolt and a hex cap screw?
Under ASME B18.2.1 a cap screw has a washer face, closer tolerances and a slightly lower head; a hex bolt is made to wider tolerances. The wrench size is the same.
Sources
- ASME B18.2.1-2012: Square, hex, heavy hex and askew head bolts and hex, heavy hex, hex flange, lobed head and lag screws (inch series)
- ASME B1.1: Unified inch screw threads (UN, UNR thread form)
- Brighton-Best: Hex head bolts / cap screws dimensional data
- AmesWeb: Hex cap screw dimensions (ASME B18.2.1)
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.