Grease Fitting Thread Size Chart (Zerk)

Grease fittings differ only in the thread and the head angle. The ball head that the grease gun coupler snaps onto is the same on all of them. In North America the standard thread is 1/4-28 SAE-LT (a short taper); European machines use M6, M8×1, M10×1 or R 1/8.

6 sizesChecked 2026-11-154 sources
Straight (A)45° (B)90° (C)
Standard head angles: straight, 45° and 90° (DIN 71412 types A, B and C). The ball head is the same on all of them and on inch and metric threads.Proportions shown, not to scale

Size chartMeasure the thread OD and pitch of the old fitting

6 of 6
ThreadThreadStandardHex across flats (type A)mminmm · inTap drill
Inch (SAE J534)
1/4-28 SAE-LT1/4-28 taper (SAE short taper)SAE J534——
1/8-27 PTF1/8-27 Dryseal taper (NPT/NPTF)SAE J534—R (0.339 in)
Metric (DIN 71412)
M6×1M6×1 (taper or straight)DIN 7141270.2765.0 mm
M8×1M8×1DIN 7141290.3547.0 mm
M10×1M10×1DIN 71412110.4339.0 mm
R 1/8 BSPTR 1/8-28 (BSPT, 55°)DIN 71412110.4338.6 mm

How to identify a grease fitting thread

Take the old fitting out and measure the thread OD with a caliper, then the pitch. About 6.3 mm (0.25 in) with 28 threads per inch is 1/4-28; 6 mm with 1 mm pitch is M6×1. They are very close (1/4-28 has a 0.91 mm pitch), and an M6 fitting forced into a 1/4-28 hole strips the thread. About 10.3 mm (0.40 in) with 27 TPI is 1/8 NPT; 9.7 mm with 28 TPI is R 1/8 BSP.

If the fitting is broken off, measure the hole: a 1/4-28 hole reads about 5.5 mm across the thread crests, an M6×1 hole about 5 mm, M8×1 about 7 mm, M10×1 about 9 mm.

The SAE-LT thread is a special short taper: it starts in a straight 1/4-28 UNF hole and wedges tight, so a 1/4-28 UNF tap is fine for repairs. Thread-cutting (self-tapping) and drive-type (press-in, 3/16 or 1/4 in) fittings exist for thin housings.

About Grease Fittings

The ball head (hydraulic nipple) and the coupler are standardised: SAE J534 and DIN 71412 heads fit the same standard 4-jaw grease gun coupler. Only special fittings need a different coupler: flush-type, button-head and giant button-head for heavy equipment.

Head angles: straight, 45° and 90° are standard (DIN 71412 types A, B and C); 65° and 30° versions exist in inch catalogues. Use an angled fitting when the straight one cannot be reached by the coupler. The angled head usually turns on its body so it can be aimed after tightening.

Tighten grease fittings gently: they have a small hex and a short thread in soft castings. Typical values are around 7–10 N·m (5–7 lbf·ft) for M6 and 1/4-28 and 10–15 N·m for M8 and M10, or snug plus a quarter turn. A fitting that will not take grease is usually blocked by hardened grease or has a stuck ball check; replace it rather than raising gun pressure.

Questions

What is the standard grease fitting thread size?

In the US and Canada, 1/4-28 SAE-LT taper. 1/8-27 PTF is the second most common. Metric machines (European and Asian) mostly use M6×1, M8×1 or M10×1; M8×1 and M10×1 are common on agricultural and construction equipment.

Is a 1/4-28 grease fitting the same as M6?

No. 1/4-28 is 6.35 mm with a 0.907 mm pitch; M6×1 is 6.0 mm with a 1.0 mm pitch. They start together but bind after two turns. Thread pitch gauges separate them instantly.

What drill size for a 1/4-28 grease fitting?

Use the tap drill for 1/4-28 UNF, then tap 1/4-28 UNF. The SAE-LT fitting's short taper seals in the straight tapped hole. For M6×1 drill 5.0 mm, M8×1 7.0 mm, M10×1 9.0 mm.

What hex size is a metric grease nipple?

DIN 71412 straight (type A) fittings: 7 mm for M6, 9 mm for M8×1 and 11 mm for M10×1 and R 1/8. Angled M6 fittings (types B and C) usually have a 9 mm hex.

Do metric and SAE grease fittings use the same grease gun?

Yes. The ball head is the same, so the standard coupler fits SAE J534 and DIN 71412 fittings alike.

Sources

  1. SAE J534: Lubrication Fittings
  2. DIN 71412: Lubricating nipples, cone type (types A, B, C)
  3. Alemite: Fittings catalogue (thread types and drill sizes)
  4. Ganter: DIN 71412 lubricating nipples data sheet

Values last checked against these sources on November 15, 2026. · How we check data

Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.