Nylon Insert Lock Nut Sizes (DIN 985, DIN 982)
A nylon insert lock nut (nyloc) has a nylon ring above the thread that grips the bolt and resists loosening. The thin DIN 985 is the common hardware-store type: an M8 is 13 mm across and 8 mm tall; the high DIN 982 is 9.5 mm tall for full nut strength.
Size chartTap a size for its drawing and full specs
| Thread | PPitchmmin | sWrench size DINmmin | Wrench size ISO (if different)mmin | hHeight DIN 985 / thin (max)mmin | Height DIN 982 / high (max)mmin |
|---|---|---|---|---|---|
| M3 | 0.50.0197 | 5.50.217 | — | 40.157 | — |
| M4 | 0.70.0276 | 70.276 | — | 50.197 | — |
| M5 | 0.80.0315 | 80.315 | — | 50.197 | — |
| M6 | 10.0394 | 100.394 | — | 60.236 | 80.315 |
| M8 | 1.250.0492 | 130.512 | — | 80.315 | 9.50.374 |
| M10 | 1.50.0591 | 170.669 | 160.630 | 100.394 | 11.50.453 |
| M12 | 1.750.0689 | 190.748 | 180.709 | 120.472 | 140.551 |
| M14 | 20.0787 | 220.866 | 210.827 | 140.551 | — |
| M16 | 20.0787 | 240.945 | — | 160.630 | 180.709 |
| M20 | 2.50.0984 | 301.181 | — | 200.787 | 220.866 |
| M24 | 30.1181 | 361.417 | — | 240.945 | — |
No exact match. The nearest sizes:
Thin (DIN 985) or high (DIN 982)?
DIN 985 (ISO 10511) is the low type: total height about one thread diameter, nylon ring included. Its metal part is shorter than a regular nut, so it is rated for lower loads (property class 6, 8 or 10 for thin nuts in steel). It is the nyloc you get in assortments.
DIN 982 (ISO 7040) is the high type: its metal part matches a full ISO 4032 nut, so it carries the full proof load of property class 8 or 10. Use it on structural joints and high-strength bolts.
The wrench size follows the DIN series (M10 17 mm, M12 19 mm, M14 22 mm). Nuts made to the ISO standards use ISO 272 sizes: M10 16 mm, M12 18 mm, M14 21 mm. Both are on the market, often in the same bin, so check before you pick a socket.
About Nylon Lock Nuts
The nylon insert has a slightly smaller bore than the thread minor diameter. When the bolt passes through, the threads form in the nylon and the elastic pressure creates a prevailing torque that holds the nut even without clamp load. The bolt must protrude at least two full threads past the nut for the lock to work.
Nylon softens with heat: the standard inserts are good to about 120 °C. Above that use all-metal prevailing torque nuts (DIN 980 / ISO 7042). Re-use reduces the locking torque; for critical joints fit a new nut each time.
Heights in the chart are maxima. ISO 10511 and ISO 7040 nuts have the same function and similar heights as DIN 985 and DIN 982, but their wrench sizes for M10, M12 and M14 are 1 mm smaller.
Fine thread and inch nyloc nuts
Fine-pitch nyloc nuts (M8×1, M10×1.25, M12×1.5) use the same body as the coarse version. Inch nylon insert nuts (ASME B18.16.6) follow the inch hex nut wrench sizes: 1/4 in takes 7/16 in, 5/16 in takes 1/2 in, 3/8 in takes 9/16 in (see inch hex nuts).
Questions
What size wrench for an M8 nyloc nut?
13 mm, for both DIN 985 and DIN 982 (and ISO). M5 takes 8 mm, M6 10 mm, M10 17 mm (ISO 16 mm), M12 19 mm (ISO 18 mm).
What is the difference between DIN 985 and DIN 982?
Height and strength. DIN 985 is the thin type (M8: 8 mm high), DIN 982 the high type (M8: 9.5 mm) with a full-height metal section for full proof load.
Can nyloc nuts be reused?
A few times on non-critical joints, but the prevailing torque drops with each use. Replace them on brakes, suspension and anything rotating or safety-relevant.
How much thread should stick out of a nyloc nut?
At least two full threads beyond the nylon ring, so the insert is fully engaged.
Sources
- DIN 985: Prevailing torque type hexagon thin nuts with non-metallic insert (superseded by ISO 10511)
- DIN 982: Prevailing torque type hexagon nuts with non-metallic insert, high type (superseded by ISO 7040)
- Aspen Fasteners: Metric DIN 985 specification
- Böllhoff: DIN 982 steel 8 data sheet
- McMaster-Carr: DIN 985 nuts
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.