Lock Washer Sizes (Split, Tooth and Conical, Metric)
Three kinds of locking washer are sold for metric bolts: the split spring washer (DIN 127 B), the toothed washer (DIN 6798) and the conical spring washer (DIN 6796). An M8 split washer is 8.1 mm inside, up to 14.8 mm outside and 2 mm thick; an M8 conical washer is 18 mm across.
Size chartTap a size for its drawing and full specs
| Bolt | d1Split DIN 127 B: inside (min)mmin | d2Split DIN 127 B: outside (max)mmin | sSplit DIN 127 B: thicknessmmin | Tooth DIN 6798: outsidemmin | Tooth DIN 6798: thicknessmmin | Conical DIN 6796: outsidemmin | Conical DIN 6796: thicknessmmin | Conical DIN 6796: height (max)mmin |
|---|---|---|---|---|---|---|---|---|
| M3 | 3.10.122 | 6.20.244 | 0.80.031 | 60.236 | 0.40.016 | 70.276 | 0.60.024 | 0.850.0335 |
| M4 | 4.10.161 | 7.60.299 | 0.90.035 | 80.315 | 0.50.020 | 90.354 | 10.039 | 1.30.0512 |
| M5 | 5.10.201 | 9.20.362 | 1.20.047 | 100.394 | 0.60.024 | 110.433 | 1.20.047 | 1.550.0610 |
| M6 | 6.10.240 | 11.80.465 | 1.60.063 | 110.433 | 0.70.028 | 140.551 | 1.50.059 | 20.0787 |
| M8 | 8.10.319 | 14.80.583 | 20.079 | 150.591 | 0.80.031 | 180.709 | 20.079 | 2.60.1024 |
| M10 | 10.20.402 | 18.10.713 | 2.20.087 | 180.709 | 0.90.035 | 230.906 | 2.50.098 | 3.20.1260 |
| M12 | 12.20.480 | 21.10.831 | 2.50.098 | 20.50.807 | 10.039 | 291.142 | 30.118 | 3.950.1555 |
| M14 | 14.20.559 | 24.10.949 | 30.118 | — | — | — | — | — |
| M16 | 16.20.638 | 27.41.079 | 3.50.138 | 261.024 | 1.20.047 | 391.535 | 40.157 | 5.250.2067 |
| M20 | 20.20.795 | 33.61.323 | 40.157 | 331.299 | 1.40.055 | 451.772 | 50.197 | 6.40.2520 |
| M24 | 24.50.965 | 401.575 | 50.197 | — | — | — | — | — |
No exact match. The nearest sizes:
Which lock washer does what
Split spring washers (DIN 127 B) are the familiar helical ring with square ends. They keep some preload on soft or settling joints. Tests (and the withdrawal of DIN 127 in the early 2000s) showed they do not prevent self-loosening of properly tightened high-strength bolts. Once flattened, they act as a plain washer.
Tooth lock washers (DIN 6798) have twisted teeth that bite into the nut and the part: form A external teeth, form J internal teeth (neater look, smaller bearing face), form V for countersunk heads. They are common in electrical work, where the teeth also make contact through paint.
Conical spring washers (DIN 6796) are hardened Belleville-type discs that keep preload in joints that settle or see temperature changes. They are designed for bolts of property class 8.8 to 10.9 and are the only type in this chart that works as a real spring at full bolt load.
About Lock Washers
All three standards are dimensioned by the bolt size, so the M8 row tells you the M8 washer of each type. The inside diameters differ: split washers fit closely (d1 min 8.1 mm for M8), tooth and conical washers use the medium clearance hole (8.4 mm).
DIN 127 and DIN 6798 were withdrawn without replacement, because research on bolted joints showed that these washers do little against self-loosening under transverse vibration. They are still produced in large numbers and are fine for low-strength screws, sheet metal and wood. For vibration-critical joints, engineers use correct preload plus a prevailing-torque nut, a threadlocker or wedge-locking washer pairs.
Wedge-locking washer pairs (Nord-Lock style, cam faces inside and serrations outside) are made to each maker's own dimensions; check the maker's table for sizes.
Questions
What is the outside diameter of an M6 lock washer?
Split DIN 127 B: 11.8 mm max (1.6 mm thick). Tooth DIN 6798: 11 mm. Conical DIN 6796: 14 mm.
Do split lock washers work?
Only on soft or settling joints. With properly tightened high-strength bolts they flatten and add no locking effect, which is why DIN 127 was withdrawn. Use a conical spring washer, a prevailing-torque nut or a threadlocker instead.
Which side of a tooth washer goes where?
Either side: the teeth are twisted symmetrically. Put it under the nut or screw head that turns, against a surface the teeth can grip.
Which way round does a conical spring washer go?
With the convex side (the raised inner edge) towards the nut or bolt head, so the washer flattens as you tighten.
Sources
- DIN 127: Spring lock washers with square or tang ends (withdrawn)
- DIN 6798: Serrated lock washers (withdrawn)
- DIN 6796:2009, Conical spring washers for bolted connections
- Westfield Fasteners: DIN 127 B spring washer table
- Westfield Fasteners: DIN 6796 conical spring washers
- Böllhoff: DIN 6798 A stainless A2 data sheet
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.