Pipe Flange Dimensions (ASME B16.5 & EN 1092-1)

Outside diameter, bolt circle, bolting and thickness of ASME B16.5 flanges (Class 150, 300, 600, NPS 1/2–24) and EN 1092-1 flanges (PN10, PN16, PN40, DN15–600). The bolt pattern depends only on size and pressure rating, never on the flange type. A 4" Class 150 weld neck, slip-on and blind flange all bolt to each other.

117 flangesChecked 2026-11-157 sources

Size chartTap a size for its drawing and full specs

117 of 117
FlangeDFlange outside diametermminmm · inKBolt circle diametermminmm · innNumber of boltsBolt sizeLBolt hole diametermminmm · intfFlange thickness (min., excl. raised face)mminmm · inRFRaised face diametermminmm · in
ASME B16.5 Class 150
1/2" Class 15088.93.5060.52.3841/2"15.95/89.70.3835.11.38
3/4" Class 15098.63.8869.92.7541/2"15.95/811.20.4442.91.69
1" Class 1501084.2579.33.1241/2"15.95/812.70.5050.82.00
1-1/4" Class 150117.44.6288.93.5041/2"15.95/814.20.5663.52.50
1-1/2" Class 1501275.0098.63.8841/2"15.95/815.80.6273.22.88
2" Class 150152.46.00120.74.7545/8"193/417.50.69923.62
2-1/2" Class 150177.87.00139.75.5045/8"193/420.80.82104.74.12
3" Class 150190.57.50152.46.0045/8"193/422.40.881275.00
3-1/2" Class 150215.98.50177.87.0085/8"193/422.40.88139.75.50
4" Class 150228.69.00190.57.5085/8"193/422.40.88157.26.19
5" Class 15025410.00215.98.5083/4"22.27/822.40.88185.77.31
6" Class 150279.411.00241.39.5083/4"22.27/823.90.94215.98.50
8" Class 150342.913.50298.511.7583/4"22.27/826.91.06269.810.62
10" Class 150406.416.0036214.25127/8"25.4128.51.12323.912.75
12" Class 150482.619.00431.817.00127/8"25.4130.21.1938115.00
14" Class 150533.421.00476.318.75121"28.61 1/833.31.31412.816.25
16" Class 150596.923.50539.821.25161"28.61 1/835.11.38469.918.50
18" Class 15063525.00577.922.75161-1/8"31.81 1/438.11.50533.421.00
20" Class 150698.527.5063525.00201-1/8"31.81 1/441.21.62584.223.00
24" Class 150812.832.00749.329.50201-1/4"34.91 3/8461.81692.227.25
ASME B16.5 Class 300
1/2" Class 30095.33.7566.62.6241/2"15.95/812.70.5035.11.38
3/4" Class 300117.44.6282.63.2545/8"193/414.20.5642.91.69
1" Class 3001244.8888.93.5045/8"193/415.80.6250.82.00
1-1/4" Class 300133.45.2598.63.8845/8"193/417.50.6963.52.50
1-1/2" Class 300155.56.12114.34.5043/4"22.27/819.10.7573.22.88
2" Class 300165.16.501275.0085/8"193/420.80.82923.62
2-1/2" Class 300190.57.50149.45.8883/4"22.27/823.90.94104.74.12
3" Class 300209.68.25168.26.6283/4"22.27/826.91.061275.00
3-1/2" Class 300228.69.00184.27.2583/4"22.27/828.51.12139.75.50
4" Class 30025410.00200.27.8883/4"22.27/830.21.19157.26.19
5" Class 300279.411.002359.2583/4"22.27/833.31.31185.77.31
6" Class 300317.512.50269.810.62123/4"22.27/835.11.38215.98.50
8" Class 30038115.00330.213.00127/8"25.4139.61.56269.810.62
10" Class 300444.517.50387.415.25161"28.61 1/8461.81323.912.75
12" Class 300520.720.50450.917.75161-1/8"31.81 1/449.31.9438115.00
14" Class 300584.223.00514.420.25201-1/8"31.81 1/452.32.06412.816.25
16" Class 300647.725.50571.522.50201-1/4"34.91 3/855.62.19469.918.50
18" Class 300711.228.00628.724.75241-1/4"34.91 3/858.72.31533.421.00
20" Class 300774.730.50685.827.00241-1/4"34.91 3/8622.44584.223.00
24" Class 300914.436.00812.832.00241-1/2"41.31 5/868.32.69692.227.25
ASME B16.5 Class 600
1/2" Class 60095.33.7566.62.6241/2"15.95/814.20.5635.11.38
3/4" Class 600117.44.6282.63.2545/8"193/415.80.6242.91.69
1" Class 6001244.8888.93.5045/8"193/417.50.6950.82.00
1-1/4" Class 600133.45.2598.63.8845/8"193/420.60.8163.52.50
1-1/2" Class 600155.56.12114.34.5043/4"22.27/822.40.8873.22.88
2" Class 600165.16.501275.0085/8"193/425.41.00923.62
2-1/2" Class 600190.57.50149.45.8883/4"22.27/828.51.12104.74.12
3" Class 600209.68.25168.26.6283/4"22.27/831.81.251275.00
3-1/2" Class 600228.69.00184.27.2587/8"25.4135.11.38139.75.50
4" Class 600273.110.75215.98.5087/8"25.4138.11.50157.26.19
5" Class 600330.213.00266.710.5081"28.61 1/844.51.75185.77.31
6" Class 600355.614.00292.111.50121"28.61 1/847.81.88215.98.50
8" Class 600419.116.50349.313.75121-1/8"31.81 1/455.62.19269.810.62
10" Class 60050820.00431.817.00161-1/4"34.91 3/863.52.50323.912.75
12" Class 600558.822.0048919.25201-1/4"34.91 3/866.62.6238115.00
14" Class 600603.323.75527.120.75201-3/8"38.11 1/269.92.75412.816.25
16" Class 600685.827.00603.323.75201-1/2"41.31 5/876.23.00469.918.50
18" Class 60074329.25654.125.75201-5/8"44.41 3/482.63.25533.421.00
20" Class 600812.832.00723.928.50241-5/8"44.41 3/488.93.50584.223.00
24" Class 600939.837.00838.233.00241-7/8"50.82101.64.00692.227.25
EN 1092-1 PN10
DN15 PN10953.74652.564M12140.55——
DN20 PN101054.13752.954M12140.55——
DN25 PN101154.53853.354M12140.55——
DN32 PN101405.511003.944M16180.71——
DN40 PN101505.911104.334M16180.71——
DN50 PN101656.501254.924M16180.71——
DN65 PN101857.281455.718M16180.71——
DN80 PN102007.871606.308M16180.71——
DN100 PN102208.661807.098M16180.71——
DN125 PN102509.842108.278M16180.71——
DN150 PN1028511.222409.458M20220.87——
DN200 PN1034013.3929511.618M20220.87——
DN250 PN1039515.5535013.7812M20220.87——
DN300 PN1044517.5240015.7512M20220.87——
DN350 PN1050519.8846018.1116M20220.87——
DN400 PN1056522.2451520.2816M24261.02——
DN450 PN1061524.2156522.2420M24261.02——
DN500 PN1067026.3862024.4120M24261.02——
DN600 PN1078030.7172528.5420M27301.18——
EN 1092-1 PN16
DN15 PN16953.74652.564M12140.55——
DN20 PN161054.13752.954M12140.55——
DN25 PN161154.53853.354M12140.55——
DN32 PN161405.511003.944M16180.71——
DN40 PN161505.911104.334M16180.71——
DN50 PN161656.501254.924M16180.71——
DN65 PN161857.281455.718M16180.71——
DN80 PN162007.871606.308M16180.71——
DN100 PN162208.661807.098M16180.71——
DN125 PN162509.842108.278M16180.71——
DN150 PN1628511.222409.458M20220.87——
DN200 PN1634013.3929511.6112M20220.87——
DN250 PN1640515.9435513.9812M24261.02——
DN300 PN1646018.1141016.1412M24261.02——
DN350 PN1652020.4747018.5016M24261.02——
DN400 PN1658022.8352520.6716M27301.18——
DN450 PN1664025.2058523.0320M27301.18——
DN500 PN1671528.1565025.5920M30331.30——
DN600 PN1684033.0777030.3120M33361.42——
EN 1092-1 PN40
DN15 PN40953.74652.564M12140.55——
DN20 PN401054.13752.954M12140.55——
DN25 PN401154.53853.354M12140.55——
DN32 PN401405.511003.944M16180.71——
DN40 PN401505.911104.334M16180.71——
DN50 PN401656.501254.924M16180.71——
DN65 PN401857.281455.718M16180.71——
DN80 PN402007.871606.308M16180.71——
DN100 PN402359.251907.488M20220.87——
DN125 PN4027010.632208.668M24261.02——
DN150 PN4030011.812509.848M24261.02——
DN200 PN4037514.7632012.6012M27301.18——
DN250 PN4045017.7238515.1612M30331.30——
DN300 PN4051520.2845017.7216M30331.30——
DN350 PN4058022.8351020.0816M33361.42——
DN400 PN4066025.9858523.0316M36391.54——
DN450 PN4068526.9761024.0220M36391.54——
DN500 PN4075529.7267026.3820M39421.65——
DN600 PN4089035.0479531.3020M45481.89——

How to identify a flange

Measure three things: the outside diameter, the bolt circle (centre of one hole to the centre of the opposite hole; on a flange with an odd hole count this is impossible, but all B16.5 and EN 1092-1 flanges have 4, 8, 12, 16, 20 or 24 holes) and the hole diameter. Count the holes. Those four numbers identify the standard, size and rating almost every time; look for the row in the chart that matches.

ASME B16.5 flanges are marked with the NPS and class, e.g. 4" 150# RF A105. The class (150, 300, 400, 600, 900, 1500, 2500) is a pressure–temperature rating group, not a pressure in psi: a Class 150 carbon steel (group 1.1) flange is rated about 285 psig at ambient temperature and less when hot. EN 1092-1 flanges are marked with DN and PN, e.g. DN100 PN16 11 B1. PN16 means 16 bar at room temperature for the reference material, and the 11 is the flange type (weld neck); B1 is the facing (raised face).

The bolt hole is always larger than the bolt: ASME holes are 1/8" over the bolt diameter (5/8" bolt in a 0.75" hole), EN holes 2–3 mm over (M16 in 18 mm, M20 in 22 mm). From the hole size you can therefore work out the bolt even when the flange is bare.

About Pipe Flanges

A flange's mating dimensions (outside diameter, bolt circle, number and size of holes, and raised face diameter) are fixed by the size and rating alone. The flange type (weld neck, slip-on, socket weld, threaded, lap joint, blind) only changes the hub and bore. That is why one chart covers all types for the dimensions that matter when you bolt two flanges together.

Thickness in ASME B16.5. Since the 2003 edition, B16.5 lists the minimum flange thickness without the raised face for every class. For Class 150 and 300 the 1/16" (1.6 mm) raised face comes on top; for Class 600 and higher, the 1/4" (6.4 mm) raised face always came on top. Older charts and many supplier catalogues still show Class 150/300 thickness including the raised face, so they read 0.06" more (2" Class 150: 0.75" instead of 0.69"). Both are right; check which convention a drawing uses.

Thickness in EN 1092-1 depends on the flange type: a type 01 plate flange, a type 05 blind, a type 11 weld neck and a type 12 slip-on hubbed flange of the same DN and PN have different thicknesses (and the standard also varies some by material). We therefore list only the common mating dimensions for EN flanges. Take the thickness from the table for your flange type.

Pipe outside diameter is listed for reference: ASME flanges fit pipe to ASME B36.10M (NPS 2 = 2.375", 60.3 mm); EN flanges fit pipe to EN 10220 / ISO 4200 series 1, which uses the same outside diameters as NPS pipe from DN15 to DN300 (DN50 = 60.3 mm). Some European flanges are also made for the series 2/3 tube sizes used in stainless and copper work, so check the bore marking.

Will an ASME flange bolt to an EN (DIN) flange?

Usually not. A 2" Class 150 flange has 4 bolts on a 120.7 mm (4.75") circle; a DN50 PN16 flange has 4 bolts on a 125 mm circle. The 4.3 mm difference is more than the hole clearance, so the bolts will not go through. A few combinations come close, such as 4" Class 150 (190.5 mm, 8 holes) against DN100 PN40 (190 mm, 8 holes), but the hole sizes, gasket dimensions and pressure ratings still differ. Use an adapter flange or a flange drilled to both patterns rather than forcing it.

Inside the EN system, PN10 and PN16 share the same drilling up to DN150 (and DN200 differs only in bolt count: 8 vs 12). PN25 and PN40 share drilling up to DN150. The flange finder above compares any two flanges.

Classes and PN ratings are not interchangeable numbers

ASME classes roughly correspond to PN values in EN 1759-1 (the Class-designated European standard): Class 150 ≈ PN20, Class 300 ≈ PN50, Class 600 ≈ PN110. EN 1759-1 flanges have the ASME bolt patterns, not the EN 1092-1 ones. A "PN16" flange and a "Class 150" flange are different products even though both are used around 16–20 bar.

Bolting

ASME B16.5 flanges use inch stud bolts (UNC up to 1", 8-UN above) with heavy hex nuts; EN 1092-1 flanges use metric bolts to the sizes listed. Stud length depends on both flange thicknesses, the gasket, and the facing, so it is not part of the flange table. B16.5 Annex tables and EN 1515 give recommended lengths.

Questions

What is the bolt pattern of a 2 inch Class 150 flange?

4 bolts, 5/8" diameter, on a 4.75" (120.7 mm) bolt circle, in 0.75" holes. The flange OD is 6.00" (152.4 mm). The same drilling applies to weld neck, slip-on, threaded and blind flanges.

What is the difference between Class 150 and Class 300 flanges?

Class 300 flanges are thicker, larger in OD and bolt circle, and from 2" upward use more or larger bolts. A 4" Class 150 flange is 9.00" OD with 8 × 5/8" bolts on 7.50"; a 4" Class 300 is 10.00" OD with 8 × 3/4" bolts on 7.88". They do not bolt together.

Are PN10 and PN16 flanges the same?

Up to DN150 they have identical drilling and bolt together. From DN200 the bolt count or bolt size differs (DN200: 8 × M20 for PN10, 12 × M20 for PN16; DN250: 12 × M20 vs 12 × M24). Thickness may differ at every size depending on the flange type.

Can I connect an ANSI flange to a DIN flange?

Not directly in most sizes. NPS 2 Class 150 has a 120.7 mm bolt circle, DN50 PN16 a 125 mm one; the bolts will not line up. Use an adapter flange or a flange drilled to the other standard. The flange finder above checks any pair.

Does the flange thickness include the raised face?

In current ASME B16.5 tables, no. The minimum thickness excludes the 1/16" raised face of Class 150/300 and the 1/4" raised face of Class 600 and up. Many older charts add the 1/16" for Class 150/300, so they read 0.06" thicker.

Sources

  1. ASME B16.5-2020: Pipe Flanges and Flanged Fittings: NPS 1/2 Through NPS 24 Metric/Inch Standard
  2. EN 1092-1:2018, Flanges and their joints. Circular flanges for pipes, valves, fittings and accessories, PN designated. Steel flanges
  3. Project Materials: Class 150 / 300 / 600 flange dimension charts (ASME B16.5)
  4. pipedata.org: Weld neck flange dimensions, ASME B16.5 (inch and mm)
  5. RoyMech: BS EN 1092-1 PN16 flange dimensions and bolting
  6. piping-world.com: Dimensions of EN 1092-1 PN16 weld neck flanges
  7. Texas Flange: ANSI B16.5 Class 600 forged flange dimensions

Values last checked against these sources on November 15, 2026. · How we check data

Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.