Butt-Weld Pipe Fitting Dimensions (ASME B16.9)

Centre-to-end and end-to-end dimensions of ASME B16.9 butt-welding fittings from NPS 1/2 to 24: 90° long- and short-radius elbows, 45° elbows, straight tees, reducers and caps. The rule of thumb that covers most of the chart: a 90° long-radius elbow is 1.5 × NPS centre to end, a short-radius elbow 1.0 × NPS.

20 sizesChecked 2026-11-155 sources

Size chartTap a size for its drawing and full specs

20 of 20
SizeODPipe outside diametermminA90° elbow, long radius (centre to end)mminA90° elbow, short radius (centre to end)mminB45° elbow, long radius (centre to end)mminCTee, centre to end of runmminHReducer, end to endmminECap length (standard wall)mminE₁Cap length (heavy wall)mmin
NPS 1/221.30.84038.11.50—15.70.6225.41.00—25.41.0025.41.00
NPS 3/426.71.05028.41.12—11.20.4428.41.1238.11.5025.41.0025.41.00
NPS 133.41.31538.11.5025.41.0022.40.8838.11.5050.82.0038.11.5038.11.50
NPS 1-1/442.21.66047.81.8831.81.2525.41.0047.81.8850.82.0038.11.5038.11.50
NPS 1-1/248.31.90057.22.2538.11.5028.41.1257.22.2563.52.5038.11.5038.11.50
NPS 260.32.37576.23.0050.82.0035.11.3863.52.5076.23.0038.11.5044.41.75
NPS 2-1/273.02.87595.33.7563.52.5044.41.7576.23.0088.93.5038.11.5050.82.00
NPS 388.93.500114.34.5076.23.0050.82.0085.93.3888.93.5050.82.0063.52.50
NPS 3-1/2101.64.000133.45.2588.93.5057.22.2595.33.75101.64.0063.52.5076.23.00
NPS 4114.34.500152.46.00101.64.0063.52.50104.64.12101.64.0063.52.5076.23.00
NPS 5141.35.563190.57.50127.05.0079.23.12124.04.88127.05.0076.23.0088.93.50
NPS 6168.36.625228.69.00152.46.0095.33.75142.75.62139.75.5088.93.50101.64.00
NPS 8219.18.625304.812.00203.28.00127.05.00177.87.00152.46.00101.64.00127.05.00
NPS 10273.110.750381.015.00254.010.00158.86.25215.98.50177.87.00127.05.00152.46.00
NPS 12323.812.750457.218.00304.812.00190.57.50254.010.00203.28.00152.46.00177.87.00
NPS 14355.614.000533.421.00355.614.00222.38.75279.411.00330.213.00165.16.50190.57.50
NPS 16406.416.000609.624.00406.416.00254.010.00304.812.00355.614.00177.87.00203.28.00
NPS 18457.218.000685.827.00457.218.00285.811.25342.913.50381.015.00203.28.00228.69.00
NPS 20508.020.000762.030.00508.020.00317.512.50381.015.00508.020.00228.69.00254.010.00
NPS 24609.624.000914.436.00609.624.00381.015.00431.817.00508.020.00266.710.50304.812.00

How the dimensions are measured

Centre to end is measured from the intersection of the two pipe centre lines to the welding end face of the fitting. For a 90° elbow it equals the bend radius: a 4" long-radius (LR) elbow has a 6.00" bend radius and its two faces are each 6.00" from the corner point. Add this to the pipe lengths when you lay out a run: cut length = centre-to-centre distance − both fitting centre-to-end dimensions − root gaps.

Long radius (LR) elbows have a bend radius of 1.5 × NPS (except NPS 1/2 and 3/4, which are 1.50" and 1.12"); short radius (SR) elbows have 1.0 × NPS and are only made from NPS 1 up. A 45° elbow uses the same long radius; its centre to end is about 5/8 × NPS (6" → 3.75"), rounded up in the small sizes.

On a straight tee the run (C) and the outlet (M) centre-to-end are equal. Reducing tees keep the run dimension C of the large size and have their own outlet dimension M. Reducers have one end-to-end length H per large-end size, whatever the small end. Caps have length E for walls up to a limiting thickness and the longer E₁ for heavier walls.

None of these dimensions change with the schedule: a Schedule 40 and a Schedule 160 2" elbow have the same 3.00" centre to end. The schedule only changes the wall, which must match the pipe.

About Butt-Weld Fittings

ASME B16.9 covers factory-made wrought butt-welding fittings (elbows, returns, tees, crosses, reducers, caps and stub ends) in NPS 1/2 through 48. The dimensions here are the standard's inch values for the sizes most often used, NPS 1/2 to 24. Fittings made to B16.9 by any manufacturer are dimensionally interchangeable, so a piping isometric can be dimensioned from this table before the fittings are bought.

The metric equivalents shown are exact conversions of the inch values. B16.9's own metric tables round them to whole millimetres (a 2" LR elbow is listed as 76 mm, the conversion is 76.2 mm), which is why metric charts sometimes differ by a few tenths.

For the pipe itself, see Pipe Sizes; the fitting OD and wall must match the pipe schedule. For flanged joints at the ends of a run, see Pipe Flanges. Socket-weld and threaded fittings (ASME B16.11) have different, much shorter dimensions and are not listed here.

Long or short radius?

Long-radius elbows are the default in process piping: lower pressure drop, less erosion and a smoother path for pigs. Short-radius elbows save space (a 6" SR elbow is 6.00" centre to end instead of 9.00"), but the pressure rating of an SR elbow may be lower than that of the straight pipe (B16.9 notes this), so check before using them in high-pressure lines.

Laying out with elbows: a worked example

Two 3" LR elbows form an offset with 30" between the parallel pipe centre lines. Each elbow takes 4.50" from centre to end, so the straight piece between them is 30 − 2 × 4.50 = 21.00" minus two root gaps (typically 1/16"–1/8" each).

Questions

What is the center to end of a 2 inch 90 degree elbow?

3.00" (76.2 mm) for a long-radius elbow and 2.00" (50.8 mm) for a short-radius elbow, per ASME B16.9. A 2" 45° elbow is 1.38" (35 mm).

How do I calculate the center to end of a long radius elbow?

Multiply the NPS by 1.5 for sizes from 1" up: 4" → 6.00", 6" → 9.00", 12" → 18.00". NPS 1/2 and 3/4 are exceptions (1.50" and 1.12"). For short radius, use 1.0 × NPS.

What is the center to end of a 4 inch tee?

4.12" (104.8 mm) for both the run and the outlet of a straight (equal) tee per ASME B16.9.

Do fitting dimensions change with schedule?

No. B16.9 centre-to-end dimensions depend only on NPS. A Schedule 40 and a Schedule 80 elbow of the same size are equally long; only the wall thickness differs, and it must match the pipe.

How long is a 6 inch concentric reducer?

5.50" (139.7 mm) end to end for any reducer with a 6" large end (6 × 4, 6 × 3, …). Eccentric reducers have the same length.

Sources

  1. ASME B16.9-2018: Factory-Made Wrought Buttwelding Fittings
  2. ASME B16.9-2003 (incorporated by reference, public copy): law.resource.org
  3. pipedata.org: Straight tee, concentric reducer and cap dimensions, ASME B16.9
  4. Ferrobend: ANSI/ASME B16.9 fitting dimension tables (mm)
  5. pipingengineer.org: Butt weld cap inch dimensions per ASME B16.9

Values last checked against these sources on November 15, 2026. · How we check data

Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.