PC Fan Sizes: Mounting Hole Spacing, Thickness, Connectors
A fan's size is the outside width of its square frame; the screws sit closer together. A 120 mm fan has its holes 105 mm apart, a 140 mm fan 124.5 mm, an 80 mm fan 71.5 mm. Measure the hole spacing centre to centre if the label is gone: it identifies the size reliably.
Fan size chartTap a size for its drawing, hole spacing and pinout
| Fan | AFrame sizemmin | BHole spacing (centre to centre)mmin | Common thicknesses | Typical use |
|---|---|---|---|---|
| 40 mm fan | 401.57 | 321.26 | 10, 20, 28 mm | Small form factor, chipset and VRM coolers, 1U servers, 3D printers |
| 50 mm fan | 501.97 | 401.57 | 10, 15 mm | Small devices, chipset coolers, 3D printer hot ends |
| 60 mm fan | 602.36 | 501.97 | 10, 15, 25 mm | Small cases, NAS, low-profile coolers |
| 70 mm fan | 702.76 | 602.36 | 15, 25 mm | Older low-profile CPU coolers, small enclosures |
| 80 mm fan | 803.15 | 71.52.81 | 15, 25, 38 mm | Older and small cases, NAS, power supplies |
| 92 mm fan | 923.62 | 82.53.25 | 14, 25, 38 mm | Compact CPU coolers, small cases, NAS |
| 120 mm fan | 1204.72 | 1054.13 | 15, 25, 38 mm | Standard case fan, tower CPU coolers, 120/240/360 mm radiators |
| 140 mm fan | 1405.51 | 124.54.90 | 25 mm (some 27–30 mm) | Case fans, large tower coolers, 140/280/420 mm radiators |
| 180 mm fan | 1807.09 | varies by maker | about 30–33 mm | Large intake fans in some cases; mounting varies by maker |
| 200 mm fan | 2007.87 | 1546.06 | 20, 30 mm | Large case intake/exhaust (check the case's hole pattern) |
No exact match. The nearest sizes:
How to measure a fan
Measure the frame from one edge to the other: 119–120 mm is a 120 mm fan. If the fan is mounted and you can only see the screws, measure from the centre of one screw to the centre of the next along a side and look it up in the chart. Thickness is the depth of the frame front to back; 25 mm is standard, "slim" fans are 12–15 mm.
Part numbers often encode the size: 12025 = 120 × 120 × 25 mm, 8015 = 80 × 80 × 15 mm, 4010 = 40 × 40 × 10 mm.
Case and radiator mounts are sized by fan count: a 240 mm radiator takes two 120 mm fans, 280 mm two 140 mm, 360 mm three 120 mm. The radiator's hole spacing therefore follows the fans' (105 mm or 124.5 mm), with fans placed 120 or 140 mm apart.
About Case Fan Sizes
Fans are mounted with coarse self-tapping fan screws into the plastic frame when they go on a case panel, and with machine screws (M3 or UNC 6-32, depending on the radiator) passing through the whole frame when they go on a radiator. Radiator screws must be long enough for the fan thickness plus the radiator's mounting plate, but not so long that they reach the radiator's fins or tubes.
A bigger fan moves the same air at lower speed and with less noise, so cases moved from 80 mm to 120 and 140 mm fans. 140 mm fans do not always fit 120 mm positions; some cases and radiators have slotted holes for both, and a few 140 mm fans add a second set of 105 mm holes. 200 mm fans are the least standardized: check the case's hole pattern before buying.
PC fans run on 12 V. 3-pin fans are controlled by changing the supply voltage (DC mode); 4-pin fans keep 12 V and take a 25 kHz PWM speed signal on pin 4. Both plug into the same motherboard header: a 3-pin plug fits a 4-pin header (pin 4 left free), and a 4-pin fan on a 3-pin header runs at full speed unless the header varies the voltage.
Fan sizes and hole spacing at a glance
| Fan | Hole spacing | Radiator sizes |
|---|---|---|
| 40 mm | 32 mm | — |
| 60 mm | 50 mm | — |
| 80 mm | 71.5 mm | — |
| 92 mm | 82.5 mm | 92 mm |
| 120 mm | 105 mm | 120, 240, 360, 480 mm |
| 140 mm | 124.5 mm | 140, 280, 420 mm |
| 200 mm | 154 mm (check the case) | — |
Other fan connectors
Molex 4-pin (peripheral) adapters run fans at a fixed 12 V (or 5 V / 7 V with resistor adapters). Many current fans with RGB lighting have a separate 3-pin 5 V ARGB plug (5 V, data, ground) or 4-pin 12 V RGB plug; these never go on a fan header. Laptop and graphics card fans use small proprietary connectors.
Questions
What is the hole spacing of a 120 mm fan?
105 mm centre to centre, in a square. A 140 mm fan uses 124.5 mm, a 92 mm fan 82.5 mm and an 80 mm fan 71.5 mm.
Can I put a 140 mm fan where a 120 mm fan goes?
Only if the mount has holes for both or the fan has a second 105 mm hole set. A 140 mm frame is 20 mm wider, so check the space too.
What is the difference between 3-pin and 4-pin fans?
A 4-pin fan adds a PWM control wire (pin 4, 25 kHz) and is controlled at constant 12 V; a 3-pin fan is controlled by varying the voltage. Both share pins 1–3 (ground, +12 V, tach) and fit the same header.
How thick is a standard case fan?
25 mm. Slim fans are 12–15 mm and high-pressure fans 38 mm thick.
What does 12025 mean on a fan?
120 × 120 mm frame, 25 mm thick. Likewise 9225 is 92 × 92 × 25 mm and 4010 is 40 × 40 × 10 mm.
Sources
- Arctic: Fan mounting hole pattern drawings (40 mm, 120 mm, 140 mm)
- Noctua: 120 mm and 140 mm fan mounting (NF-P14 / NF-A14 dual hole pattern)
- Intel: 4-Wire Pulse Width Modulation (PWM) Controlled Fans specification, rev. 1.3
- Voltcave: How to measure a PC fan's size (fan size vs hole spacing table)
- Wikipedia: Computer fan (fan size vs mounting hole spacing table, connectors)
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.