SAE and USS Flat Washer Sizes
SAE washers are the narrow series: a close-fitting hole and a smaller outside diameter, sized for hex heads and nuts on machinery. USS washers are the wide series with a looser hole and a larger OD for wood and soft materials. For a 1/4 in bolt: SAE 0.281 × 0.625 in, USS 0.312 × 0.734 in.
Size chartTap a size for its drawing and full specs
| Washer | IDInside diametermmin | ODOutside diametermmin | tThickness (nominal)mmin |
|---|---|---|---|
| SAE: narrow series (N) | |||
| #6 SAE | 4.00.156 | 9.50.375 | 1.240.049 |
| #8 SAE | 4.80.188 | 11.10.438 | 1.240.049 |
| #10 SAE | 5.60.219 | 12.70.500 | 1.240.049 |
| #12 SAE | 6.40.250 | 14.30.562 | 1.650.065 |
| 1/4" SAE | 7.10.281 | 15.90.625 | 1.650.065 |
| 5/16" SAE | 8.70.344 | 17.50.688 | 1.650.065 |
| 3/8" SAE | 10.30.406 | 20.60.812 | 1.650.065 |
| 7/16" SAE | 11.90.469 | 23.40.922 | 1.650.065 |
| 1/2" SAE | 13.50.531 | 27.01.062 | 2.410.095 |
| 9/16" SAE | 15.10.594 | 29.41.156 | 2.410.095 |
| 5/8" SAE | 16.70.656 | 33.31.312 | 2.410.095 |
| 3/4" SAE | 20.60.812 | 37.31.469 | 3.400.134 |
| 7/8" SAE | 23.80.938 | 44.41.750 | 3.400.134 |
| 1" SAE | 27.01.062 | 50.82.000 | 3.400.134 |
| USS: wide series (W) | |||
| 1/4" USS | 7.90.312 | 18.60.734 | 1.650.065 |
| 5/16" USS | 9.50.375 | 22.20.875 | 2.110.083 |
| 3/8" USS | 11.10.438 | 25.41.000 | 2.110.083 |
| 7/16" USS | 12.70.500 | 31.81.250 | 2.110.083 |
| 1/2" USS | 14.30.562 | 34.91.375 | 2.770.109 |
| 9/16" USS | 15.90.625 | 37.31.469 | 2.770.109 |
| 5/8" USS | 17.50.688 | 44.41.750 | 3.400.134 |
| 3/4" USS | 20.60.812 | 50.82.000 | 3.760.148 |
| 7/8" USS | 23.80.938 | 57.22.250 | 4.190.165 |
| 1" USS | 27.01.062 | 63.52.500 | 4.190.165 |
| 1-1/8" USS | 31.81.250 | 69.92.750 | 4.190.165 |
| 1-1/4" USS | 34.91.375 | 76.23.000 | 4.190.165 |
| 1-3/8" USS | 38.11.500 | 82.63.250 | 4.570.180 |
| 1-1/2" USS | 41.31.625 | 88.93.500 | 4.570.180 |
No exact match. The nearest sizes:
SAE or USS?
The washer size is the bolt size it is for, not its hole: a 1/4 in SAE washer has a 0.281 in (9/32) hole, a 1/4 in USS washer a 0.312 in (5/16) hole. All values are basic (nominal) per ASME B18.22.1 Type A; real washers vary by a few thousandths, thickness by up to about ±0.010 in.
SAE (narrow, N) fits snugly around the bolt and under a standard hex head without overhang. It is the normal choice for machinery and automotive work. USS (wide, W) spreads load on wood and soft materials and covers oversize holes; it is thicker in most sizes.
Fender washers have a much larger OD than USS (often 1 to 2 in on a 1/4 in hole) and are sold by hole × OD, e.g. 1/4 × 1-1/4 in. There is no single standard for them, so check the listing.
About SAE & USS Washers
In ASME B18.22.1, the plain washer Type A comes in a narrow series (N) and a wide series (W); in hardware stores these are called SAE and USS. Through-hardened washers for structural bolts (ASTM F436) have their own, slightly different dimensions.
Use a washer under the turning part (usually the nut) to protect the surface and get consistent friction when tightening. Under a bolt head with a washer face, a washer is only needed on soft materials or slotted holes.
Metric washers (ISO 7089 / DIN 125) are listed separately under metric washers. A 1/4 in SAE washer is close to an M6 washer (6.4 × 12 mm) but not identical.
Questions
What is the difference between SAE and USS washers?
SAE washers have a smaller hole and smaller outside diameter (1/2 in: 0.531 × 1.062 in); USS washers have a larger hole and outside diameter and are usually thicker (1/2 in: 0.562 × 1.375 × 0.109 in).
What size is a 3/8 SAE washer?
0.406 in (13/32) inside, 0.812 in (13/16) outside, 0.065 in thick.
What size is a 3/8 USS washer?
0.438 in (7/16) inside, 1.000 in outside, 0.083 in thick.
Can I use a USS washer on a machine bolt?
Yes, but its loose hole lets it shift off-centre and its OD overhangs the hex head. SAE washers are the better fit for machinery; USS for wood and soft materials.
Sources
- ASME B18.22.1: Plain washers (Type A narrow and wide series)
- Bolt Depot: USS and SAE flat washer size charts
- AmesWeb: Type A plain washers dimensions chart
- GlobalSpec: Washers information (N = SAE, W = USS)
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.