C11/h11 Fit Tolerances

ISO Fits · Shaft-basis fits (h shaft)

C11/h11: Clearance fit, Shaft-basis fits (h shaft). At ⌀25 mm the hole is +240 / +110 µm, the shaft 0 / −130 µm, giving a maximum clearance of 370 µm and a minimum clearance of 110 µm (negative = interference). The table below lists the limits for every ISO size range up to 500 mm.

Fit type
Clearance
Max. clearance at ⌀25 mm
370 µm0.01457 in0.01457 in370 µm
Min. clearance at ⌀25 mm (− = interference)
110 µm0.00433 in0.00433 in110 µm

Drawing

zero line = nominal sizeHole C11Shaft h11+240+1100−130⌀25 C11/h11: clearance 110 to 370 µm
Tolerance zones at ⌀25 mm, deviations in µm; vertical scale enlarged.Proportions shown, not to scale

C11/h11 specifications

Fit typeClearance
Hole limits at ⌀25 mm (µm)+240 / +110
Shaft limits at ⌀25 mm (µm)0 / −130
Max. clearance at ⌀25 mm370 µm0.01457 in
Min. clearance at ⌀25 mm (− = interference)110 µm0.00433 in

C11/h11 limits for every size range (µm)

Size (mm)Hole ES / EIShaft es / eiMax. clearanceMin. clearanceType
≤ 3+120 / +600 / −60+180+60clearance
3–6+145 / +700 / −75+220+70clearance
6–10+170 / +800 / −90+260+80clearance
10–18+205 / +950 / −110+315+95clearance
18–30+240 / +1100 / −130+370+110clearance
30–40+280 / +1200 / −160+440+120clearance
40–50+290 / +1300 / −160+450+130clearance
50–65+330 / +1400 / −190+520+140clearance
65–80+340 / +1500 / −190+530+150clearance
80–100+390 / +1700 / −220+610+170clearance
100–120+400 / +1800 / −220+620+180clearance
120–140+450 / +2000 / −250+700+200clearance
140–160+460 / +2100 / −250+710+210clearance
160–180+480 / +2300 / −250+730+230clearance
180–200+530 / +2400 / −290+820+240clearance
200–225+550 / +2600 / −290+840+260clearance
225–250+570 / +2800 / −290+860+280clearance
250–280+620 / +3000 / −320+940+300clearance
280–315+650 / +3300 / −320+970+330clearance
315–355+720 / +3600 / −360+1080+360clearance
355–400+760 / +4000 / −360+1120+400clearance
400–450+840 / +4400 / −400+1240+440clearance
450–500+880 / +4800 / −400+1280+480clearance

Shaft-basis loose running fit, the h11 equivalent of H11/c11, used with drawn bar or pins in h11.

Other fits of the same type (Clearance)

All ISO fits

Compare all 24 fits in the ISO Fits chart →

Sources

  1. ISO 286-1:2010, Geometrical product specifications (GPS): ISO code system for tolerances on linear sizes, Part 1: Basis of tolerances, deviations and fits
  2. ISO 286-2:2010, Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
  3. ANSI B4.2-1978 (R2020): Preferred metric limits and fits

Values last checked against these sources on November 15, 2026. · How we check data

Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.