H7/f7 Fit Tolerances
ISO Fits · Hole-basis fits (H hole)
H7/f7: Clearance fit, Hole-basis fits (H hole). At ⌀25 mm the hole is +21 / 0 µm, the shaft −20 / −41 µm, giving a maximum clearance of 62 µm and a minimum clearance of 20 µm (negative = interference). The table below lists the limits for every ISO size range up to 500 mm.
- Fit type
- Clearance
- Max. clearance at ⌀25 mm
- 62 µm0.00244 in0.00244 in62 µm
- Min. clearance at ⌀25 mm (− = interference)
- 20 µm0.00079 in0.00079 in20 µm
Drawing
H7/f7 specifications
| Fit type | Clearance |
|---|---|
| Hole limits at ⌀25 mm (µm) | +21 / 0 |
| Shaft limits at ⌀25 mm (µm) | −20 / −41 |
| Max. clearance at ⌀25 mm | 62 µm0.00244 in |
| Min. clearance at ⌀25 mm (− = interference) | 20 µm0.00079 in |
H7/f7 limits for every size range (µm)
| Size (mm) | Hole ES / EI | Shaft es / ei | Max. clearance | Min. clearance | Type |
|---|---|---|---|---|---|
| ≤ 3 | +10 / 0 | −6 / −16 | +26 | +6 | clearance |
| 3–6 | +12 / 0 | −10 / −22 | +34 | +10 | clearance |
| 6–10 | +15 / 0 | −13 / −28 | +43 | +13 | clearance |
| 10–18 | +18 / 0 | −16 / −34 | +52 | +16 | clearance |
| 18–30 | +21 / 0 | −20 / −41 | +62 | +20 | clearance |
| 30–50 | +25 / 0 | −25 / −50 | +75 | +25 | clearance |
| 50–80 | +30 / 0 | −30 / −60 | +90 | +30 | clearance |
| 80–120 | +35 / 0 | −36 / −71 | +106 | +36 | clearance |
| 120–180 | +40 / 0 | −43 / −83 | +123 | +43 | clearance |
| 180–250 | +46 / 0 | −50 / −96 | +142 | +50 | clearance |
| 250–315 | +52 / 0 | −56 / −108 | +160 | +56 | clearance |
| 315–400 | +57 / 0 | −62 / −119 | +176 | +62 | clearance |
| 400–500 | +63 / 0 | −68 / −131 | +194 | +68 | clearance |
Close running fit with a finer hole than H8/f7: accurate running and sliding of spindles and guided parts.
Other fits of the same type (Clearance)
H11/c11Clearance · 370 µm · 110 µmH9/d9Clearance · 169 µm · 65 µmH9/e9Clearance · 144 µm · 40 µmH8/f7Clearance · 74 µm · 20 µmH7/g6Clearance · 41 µm · 7 µmH7/h6Clearance · 34 µm · 0 µmH8/h7Clearance · 54 µm · 0 µmH11/h11Clearance · 260 µm · 0 µmC11/h11Clearance · 370 µm · 110 µmD9/h9Clearance · 169 µm · 65 µmF8/h7Clearance · 74 µm · 20 µmG7/h6Clearance · 41 µm · 7 µm
All ISO fits
Sources
- ISO 286-1:2010, Geometrical product specifications (GPS): ISO code system for tolerances on linear sizes, Part 1: Basis of tolerances, deviations and fits
- ISO 286-2:2010, Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
- ANSI B4.2-1978 (R2020): Preferred metric limits and fits
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.