H7/h6 Fit Tolerances
ISO Fits · Hole-basis fits (H hole)
H7/h6: Clearance fit, Hole-basis fits (H hole). At ⌀25 mm the hole is +21 / 0 µm, the shaft 0 / −13 µm, giving a maximum clearance of 34 µm and a minimum clearance of 0 µm (negative = interference). The table below lists the limits for every ISO size range up to 500 mm.
- Fit type
- Clearance
- Max. clearance at ⌀25 mm
- 34 µm0.00134 in0.00134 in34 µm
- Min. clearance at ⌀25 mm (− = interference)
- 0 µm0.00000 in0.00000 in0 µm
Drawing
H7/h6 specifications
| Fit type | Clearance |
|---|---|
| Hole limits at ⌀25 mm (µm) | +21 / 0 |
| Shaft limits at ⌀25 mm (µm) | 0 / −13 |
| Max. clearance at ⌀25 mm | 34 µm0.00134 in |
| Min. clearance at ⌀25 mm (− = interference) | 0 µm0.00000 in |
H7/h6 limits for every size range (µm)
| Size (mm) | Hole ES / EI | Shaft es / ei | Max. clearance | Min. clearance | Type |
|---|---|---|---|---|---|
| ≤ 3 | +10 / 0 | 0 / −6 | +16 | 0 | clearance |
| 3–6 | +12 / 0 | 0 / −8 | +20 | 0 | clearance |
| 6–10 | +15 / 0 | 0 / −9 | +24 | 0 | clearance |
| 10–18 | +18 / 0 | 0 / −11 | +29 | 0 | clearance |
| 18–30 | +21 / 0 | 0 / −13 | +34 | 0 | clearance |
| 30–50 | +25 / 0 | 0 / −16 | +41 | 0 | clearance |
| 50–80 | +30 / 0 | 0 / −19 | +49 | 0 | clearance |
| 80–120 | +35 / 0 | 0 / −22 | +57 | 0 | clearance |
| 120–180 | +40 / 0 | 0 / −25 | +65 | 0 | clearance |
| 180–250 | +46 / 0 | 0 / −29 | +75 | 0 | clearance |
| 250–315 | +52 / 0 | 0 / −32 | +84 | 0 | clearance |
| 315–400 | +57 / 0 | 0 / −36 | +93 | 0 | clearance |
| 400–500 | +63 / 0 | 0 / −40 | +103 | 0 | clearance |
Locational clearance fit. Assembled by hand without force, zero minimum clearance: spigots and recesses, locating pins in jigs, parts that must be removed often.
Other fits of the same type (Clearance)
H11/c11Clearance · 370 µm · 110 µmH9/d9Clearance · 169 µm · 65 µmH9/e9Clearance · 144 µm · 40 µmH8/f7Clearance · 74 µm · 20 µmH7/f7Clearance · 62 µm · 20 µmH7/g6Clearance · 41 µm · 7 µmH8/h7Clearance · 54 µm · 0 µmH11/h11Clearance · 260 µm · 0 µmC11/h11Clearance · 370 µm · 110 µmD9/h9Clearance · 169 µm · 65 µmF8/h7Clearance · 74 µm · 20 µmG7/h6Clearance · 41 µm · 7 µm
All ISO fits
Sources
- ISO 286-1:2010, Geometrical product specifications (GPS): ISO code system for tolerances on linear sizes, Part 1: Basis of tolerances, deviations and fits
- ISO 286-2:2010, Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
- ANSI B4.2-1978 (R2020): Preferred metric limits and fits
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.