H9/e9 Fit Tolerances
ISO Fits · Hole-basis fits (H hole)
H9/e9: Clearance fit, Hole-basis fits (H hole). At ⌀25 mm the hole is +52 / 0 µm, the shaft −40 / −92 µm, giving a maximum clearance of 144 µm and a minimum clearance of 40 µm (negative = interference). The table below lists the limits for every ISO size range up to 500 mm.
- Fit type
- Clearance
- Max. clearance at ⌀25 mm
- 144 µm0.00567 in0.00567 in144 µm
- Min. clearance at ⌀25 mm (− = interference)
- 40 µm0.00157 in0.00157 in40 µm
Drawing
H9/e9 specifications
| Fit type | Clearance |
|---|---|
| Hole limits at ⌀25 mm (µm) | +52 / 0 |
| Shaft limits at ⌀25 mm (µm) | −40 / −92 |
| Max. clearance at ⌀25 mm | 144 µm0.00567 in |
| Min. clearance at ⌀25 mm (− = interference) | 40 µm0.00157 in |
H9/e9 limits for every size range (µm)
| Size (mm) | Hole ES / EI | Shaft es / ei | Max. clearance | Min. clearance | Type |
|---|---|---|---|---|---|
| ≤ 3 | +25 / 0 | −14 / −39 | +64 | +14 | clearance |
| 3–6 | +30 / 0 | −20 / −50 | +80 | +20 | clearance |
| 6–10 | +36 / 0 | −25 / −61 | +97 | +25 | clearance |
| 10–18 | +43 / 0 | −32 / −75 | +118 | +32 | clearance |
| 18–30 | +52 / 0 | −40 / −92 | +144 | +40 | clearance |
| 30–50 | +62 / 0 | −50 / −112 | +174 | +50 | clearance |
| 50–80 | +74 / 0 | −60 / −134 | +208 | +60 | clearance |
| 80–120 | +87 / 0 | −72 / −159 | +246 | +72 | clearance |
| 120–180 | +100 / 0 | −85 / −185 | +285 | +85 | clearance |
| 180–250 | +115 / 0 | −100 / −215 | +330 | +100 | clearance |
| 250–315 | +130 / 0 | −110 / −240 | +370 | +110 | clearance |
| 315–400 | +140 / 0 | −125 / −265 | +405 | +125 | clearance |
| 400–500 | +155 / 0 | −135 / −290 | +445 | +135 | clearance |
Loose running fit with less clearance than d9; shafts in several bearings with some misalignment, plain bearings at moderate speed.
Other fits of the same type (Clearance)
H11/c11Clearance · 370 µm · 110 µmH9/d9Clearance · 169 µm · 65 µmH8/f7Clearance · 74 µm · 20 µmH7/f7Clearance · 62 µm · 20 µmH7/g6Clearance · 41 µm · 7 µmH7/h6Clearance · 34 µm · 0 µmH8/h7Clearance · 54 µm · 0 µmH11/h11Clearance · 260 µm · 0 µmC11/h11Clearance · 370 µm · 110 µmD9/h9Clearance · 169 µm · 65 µmF8/h7Clearance · 74 µm · 20 µmG7/h6Clearance · 41 µm · 7 µm
All ISO fits
Sources
- ISO 286-1:2010, Geometrical product specifications (GPS): ISO code system for tolerances on linear sizes, Part 1: Basis of tolerances, deviations and fits
- ISO 286-2:2010, Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
- ANSI B4.2-1978 (R2020): Preferred metric limits and fits
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.