H8/f7 Fit Tolerances
ISO Fits · Hole-basis fits (H hole)
H8/f7: Clearance fit, Hole-basis fits (H hole). At ⌀25 mm the hole is +33 / 0 µm, the shaft −20 / −41 µm, giving a maximum clearance of 74 µm and a minimum clearance of 20 µm (negative = interference). The table below lists the limits for every ISO size range up to 500 mm.
- Fit type
- Clearance
- Max. clearance at ⌀25 mm
- 74 µm0.00291 in0.00291 in74 µm
- Min. clearance at ⌀25 mm (− = interference)
- 20 µm0.00079 in0.00079 in20 µm
Drawing
H8/f7 specifications
| Fit type | Clearance |
|---|---|
| Hole limits at ⌀25 mm (µm) | +33 / 0 |
| Shaft limits at ⌀25 mm (µm) | −20 / −41 |
| Max. clearance at ⌀25 mm | 74 µm0.00291 in |
| Min. clearance at ⌀25 mm (− = interference) | 20 µm0.00079 in |
H8/f7 limits for every size range (µm)
| Size (mm) | Hole ES / EI | Shaft es / ei | Max. clearance | Min. clearance | Type |
|---|---|---|---|---|---|
| ≤ 3 | +14 / 0 | −6 / −16 | +30 | +6 | clearance |
| 3–6 | +18 / 0 | −10 / −22 | +40 | +10 | clearance |
| 6–10 | +22 / 0 | −13 / −28 | +50 | +13 | clearance |
| 10–18 | +27 / 0 | −16 / −34 | +61 | +16 | clearance |
| 18–30 | +33 / 0 | −20 / −41 | +74 | +20 | clearance |
| 30–50 | +39 / 0 | −25 / −50 | +89 | +25 | clearance |
| 50–80 | +46 / 0 | −30 / −60 | +106 | +30 | clearance |
| 80–120 | +54 / 0 | −36 / −71 | +125 | +36 | clearance |
| 120–180 | +63 / 0 | −43 / −83 | +146 | +43 | clearance |
| 180–250 | +72 / 0 | −50 / −96 | +168 | +50 | clearance |
| 250–315 | +81 / 0 | −56 / −108 | +189 | +56 | clearance |
| 315–400 | +89 / 0 | −62 / −119 | +208 | +62 | clearance |
| 400–500 | +97 / 0 | −68 / −131 | +228 | +68 | clearance |
Close running fit, the default for rotating shafts in plain bearings with oil lubrication, gearbox shafts in bushes, accurate sliding parts at moderate speed.
Other fits of the same type (Clearance)
H11/c11Clearance · 370 µm · 110 µmH9/d9Clearance · 169 µm · 65 µmH9/e9Clearance · 144 µm · 40 µmH7/f7Clearance · 62 µm · 20 µmH7/g6Clearance · 41 µm · 7 µmH7/h6Clearance · 34 µm · 0 µmH8/h7Clearance · 54 µm · 0 µmH11/h11Clearance · 260 µm · 0 µmC11/h11Clearance · 370 µm · 110 µmD9/h9Clearance · 169 µm · 65 µmF8/h7Clearance · 74 µm · 20 µmG7/h6Clearance · 41 µm · 7 µm
All ISO fits
Sources
- ISO 286-1:2010, Geometrical product specifications (GPS): ISO code system for tolerances on linear sizes, Part 1: Basis of tolerances, deviations and fits
- ISO 286-2:2010, Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
- ANSI B4.2-1978 (R2020): Preferred metric limits and fits
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.