F8/h7 Fit Tolerances
ISO Fits · Shaft-basis fits (h shaft)
F8/h7: Clearance fit, Shaft-basis fits (h shaft). At ⌀25 mm the hole is +53 / +20 µm, the shaft 0 / −21 µm, giving a maximum clearance of 74 µm and a minimum clearance of 20 µm (negative = interference). The table below lists the limits for every ISO size range up to 500 mm.
- Fit type
- Clearance
- Max. clearance at ⌀25 mm
- 74 µm0.00291 in0.00291 in74 µm
- Min. clearance at ⌀25 mm (− = interference)
- 20 µm0.00079 in0.00079 in20 µm
Drawing
F8/h7 specifications
| Fit type | Clearance |
|---|---|
| Hole limits at ⌀25 mm (µm) | +53 / +20 |
| Shaft limits at ⌀25 mm (µm) | 0 / −21 |
| Max. clearance at ⌀25 mm | 74 µm0.00291 in |
| Min. clearance at ⌀25 mm (− = interference) | 20 µm0.00079 in |
F8/h7 limits for every size range (µm)
| Size (mm) | Hole ES / EI | Shaft es / ei | Max. clearance | Min. clearance | Type |
|---|---|---|---|---|---|
| ≤ 3 | +20 / +6 | 0 / −10 | +30 | +6 | clearance |
| 3–6 | +28 / +10 | 0 / −12 | +40 | +10 | clearance |
| 6–10 | +35 / +13 | 0 / −15 | +50 | +13 | clearance |
| 10–18 | +43 / +16 | 0 / −18 | +61 | +16 | clearance |
| 18–30 | +53 / +20 | 0 / −21 | +74 | +20 | clearance |
| 30–50 | +64 / +25 | 0 / −25 | +89 | +25 | clearance |
| 50–80 | +76 / +30 | 0 / −30 | +106 | +30 | clearance |
| 80–120 | +90 / +36 | 0 / −35 | +125 | +36 | clearance |
| 120–180 | +106 / +43 | 0 / −40 | +146 | +43 | clearance |
| 180–250 | +122 / +50 | 0 / −46 | +168 | +50 | clearance |
| 250–315 | +137 / +56 | 0 / −52 | +189 | +56 | clearance |
| 315–400 | +151 / +62 | 0 / −57 | +208 | +62 | clearance |
| 400–500 | +165 / +68 | 0 / −63 | +228 | +68 | clearance |
Shaft-basis close running fit: several parts running on one common ground shaft.
Other fits of the same type (Clearance)
H11/c11Clearance · 370 µm · 110 µmH9/d9Clearance · 169 µm · 65 µmH9/e9Clearance · 144 µm · 40 µmH8/f7Clearance · 74 µm · 20 µmH7/f7Clearance · 62 µm · 20 µmH7/g6Clearance · 41 µm · 7 µmH7/h6Clearance · 34 µm · 0 µmH8/h7Clearance · 54 µm · 0 µmH11/h11Clearance · 260 µm · 0 µmC11/h11Clearance · 370 µm · 110 µmD9/h9Clearance · 169 µm · 65 µmG7/h6Clearance · 41 µm · 7 µm
All ISO fits
Sources
- ISO 286-1:2010, Geometrical product specifications (GPS): ISO code system for tolerances on linear sizes, Part 1: Basis of tolerances, deviations and fits
- ISO 286-2:2010, Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
- ANSI B4.2-1978 (R2020): Preferred metric limits and fits
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.