Roller Chain Sprocket Dimensions & Calculator
Sprocket dimensions follow from two numbers: the chain pitch and the tooth count. The pitch diameter is PD = p / sin(180°/N). A 17-tooth #40 sprocket (p = 1/2") has PD = 2.721". Pick a chain below for its full table from 9 to 60 teeth.
Size chartTap a size for its drawing and full specs
| Chain | pChain pitchmminmm · in | DrRoller diametermminmm · in | WWidth between inner platesmminmm · in | tTooth width, single strandmminmm · in | ISO 606 A-series equivalent |
|---|---|---|---|---|---|
| ANSI (ASME B29.1) roller chain | |||||
| #25 | 6.351/4 | 3.300.130 | 3.181/8 | 2.800.110 | 04C |
| #35 | 9.533/8 | 5.080.200 | 4.763/16 | 4.280.168 | 06C |
| #40 | 12.701/2 | 7.945/16 | 7.945/16 | 7.230.285 | 08A |
| #41 | 12.701/2 | 7.770.306 | 6.351/4 | 5.750.227 | 085 |
| #50 | 15.885/8 | 10.160.400 | 9.533/8 | 8.710.343 | 10A |
| #60 | 19.053/4 | 11.9115/32 | 12.701/2 | 11.660.459 | 12A |
| #80 | 25.401 | 15.885/8 | 15.885/8 | 14.610.575 | 16A |
| #100 | 31.751 1/4 | 19.053/4 | 19.053/4 | 17.560.692 | 20A |
| #120 | 38.101 1/2 | 22.237/8 | 25.401 | 23.470.924 | 24A |
| #140 | 44.451 3/4 | 25.401 | 25.401 | 23.470.924 | 28A |
| #160 | 50.802 | 28.581 1/8 | 31.751 1/4 | 29.381.157 | 32A |
| ISO 606 B series (European) | |||||
| 05B | 8.000.315 | 5.000.197 | 3.000.118 | — | — |
| 06B | 9.533/8 | 6.351/4 | 5.720.225 | — | — |
| 08B | 12.701/2 | 8.510.335 | 7.750.305 | — | — |
| 10B | 15.885/8 | 10.160.400 | 9.650.380 | — | — |
| 12B | 19.053/4 | 12.070.475 | 11.680.460 | — | — |
| 16B | 25.401 | 15.880.625 | 17.020.670 | — | — |
| 20B | 31.751 1/4 | 19.053/4 | 19.560.770 | — | — |
| 24B | 38.101 1/2 | 25.401 | 25.401 | — | — |
No exact match. The nearest sizes:
The sprocket formulas
Pitch diameter: the circle on which the roller centres sit when the chain wraps the sprocket: PD = p / sin(180°/N). It sets the speed ratio and the chain wrap, and it is the diameter to use in centre-distance calculations.
Outside diameter: the tip diameter of the teeth. ASME B29.1 gives the turned-blank diameter as approximately OD = p × (0.6 + cot(180°/N)); the exact tip depends on the hob or cutter, so treat it as the maximum blank size, not a gauge dimension.
Bottom diameter: the diameter at the bottom of the tooth gaps: BD = PD − Dr, with Dr the roller diameter. On a sprocket with an even tooth count, measure it directly across two opposite gaps with a caliper. With an odd count, no gap faces another, so the caliper reading is smaller: CD = PD × cos(90°/N) − Dr. Measuring over two gauge pins of roller diameter gives the same check with a micrometer.
Tooth width of ANSI single-strand sprockets is 0.93 × W − 0.006", where W is the width between the chain's inner plates; multiple-strand sprockets use slightly smaller factors and add the transverse pitch for each strand.
About Sprockets
ANSI chain numbers carry the pitch: the last digit is 0 for standard roller chain, 1 for lightweight (#41) and 5 for rollerless bushing chain (#25, #35); the digits in front are the pitch in eighths of an inch: #40 = 4/8" = 1/2", #80 = 1", #120 = 1 1/2". ISO 606 B-series (European, formerly DIN 8187) chains are named in sixteenths of an inch: 08B = 8/16" = 1/2", 16B = 1". The 05B, at 8 mm, is the only truly metric pitch.
#40 and 08B are not interchangeable even though both are 1/2" pitch: the 08B roller is 8.51 mm against 7.94 mm (0.312") and the inner width 7.75 mm against 7.94 mm. A worn chain might run on the other sprocket, but the seating curve does not match. 12B and #60, and 16B and #80 differ even more. The pitch diameter, however, depends only on pitch and N, so it is identical for #40 and 08B.
The tooth count matters for smoothness and life. With few teeth the chain rises and falls as each link engages (chordal action): speed variation is 1 − cos(180°/N), i.e. 4.9 % at 10 teeth, 1.7 % at 17 and 0.5 % at 30. Most catalogues recommend at least 17 teeth on the small sprocket for moderate to high speed drives, and odd tooth counts with an even number of chain links so wear is spread over all teeth.
Identifying an unknown sprocket
Measure the pitch on a piece of chain that fits (centre of one pin to the centre of the next), or measure the bottom/caliper diameter and count the teeth, then compare with the table for each candidate chain. A 1/2" pitch, 18-tooth sprocket has BD = 2.879 − 0.312 = 2.567" for #40, and 2.879" − 8.51 mm (0.335") = 2.544" for 08B: the 0.6 mm difference is enough to tell them apart.
Questions
How do I calculate the pitch diameter of a sprocket?
PD = p / sin(180°/N). For #40 chain (p = 0.5") and 20 teeth: 0.5 / sin 9° = 3.196" (81.18 mm). For 08B the result is the same, because the pitch is also 1/2".
What is the outside diameter of a sprocket?
Approximately p × (0.6 + cot(180°/N)). A 17-tooth #40 sprocket: 0.5 × (0.6 + 5.350) = 2.975". The real tip diameter depends on the tooth cutter and is slightly smaller on some sprockets.
How do I measure a sprocket with an odd number of teeth?
Measure the caliper diameter from the bottom of one gap to the bottom of the gap nearest opposite it: CD = PD × cos(90°/N) − Dr. On a 15-tooth #40 sprocket that is 2.405 × cos 6° − 0.312 = 2.080".
What does the number of a roller chain mean?
The leading digits are the pitch in eighths of an inch: #40 = 4/8" = 1/2", #60 = 6/8" = 3/4", #100 = 10/8" = 1 1/4". A final 0 means standard roller chain, 1 lightweight, 5 rollerless.
Can I use a #40 sprocket with 08B chain?
Not reliably. Both have a 1/2" pitch, but the 08B roller is 8.51 mm against 7.94 mm for #40, so the tooth gaps don't fit properly. Use the sprocket made for the chain standard.
Sources
- ASME B29.1-2011: Precision power transmission roller chains, attachments, and sprockets
- ISO 606:2015, Short-pitch transmission precision roller and bush chains, attachments and associated chain sprockets
- Martin Sprocket & Gear: Sprocket engineering data (formulas, tooth form)
- Engineers Edge: Roller chain sprocket diameters per ANSI/ASME B29.1M
- Ametric: American Standard (ANSI) roller chain dimensions
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.