Timing Belt Profiles: Pitch & Tooth Size Chart
Pitch, tooth height and overall height of the common synchronous (timing) belt profiles: trapezoidal inch (MXL to XH), metric T and AT, curvilinear HTD, GT2 and STD. Belts and pulleys only work together when both the pitch and the tooth profile match. A 5 mm HTD, a 5 mm GT2, a T5 and an S5M belt all have a 5 mm pitch and none of them is meant for the others' pulleys.
Size chartTap a size for its drawing and full specs
| Profile | pPitchmmin | hₜTooth heightmmin | hₛBelt height (typical)mmin | sTooth width at rootmmin | 2βTooth flank angle° | Tooth profile | Common widths |
|---|---|---|---|---|---|---|---|
| Trapezoidal, inch (ISO 5296) | |||||||
| MXL | 2.0320.080 | 0.510.020 | 1.140.045 | 1.140.045 | 40 | Trapezoidal | 3.2, 4.8, 6.4 (1/8", 3/16", 1/4") |
| XL | 5.080.200 | 1.270.050 | 2.30.091 | 2.570.101 | 50 | Trapezoidal | 6.4, 7.9, 9.5 (1/4", 5/16", 3/8") |
| L | 9.5250.375 | 1.910.075 | 3.60.142 | 4.650.183 | 40 | Trapezoidal | 12.7, 19.1, 25.4 (1/2", 3/4", 1") |
| H | 12.70.500 | 2.290.090 | 4.30.169 | 6.120.241 | 40 | Trapezoidal | 19.1, 25.4, 38.1, 50.8, 76.2 (3/4"–3") |
| XH | 22.2250.875 | 6.350.250 | 11.20.441 | 12.570.495 | 40 | Trapezoidal | 50.8, 76.2, 101.6 (2", 3", 4") |
| Trapezoidal, metric T (DIN 7721) | |||||||
| T2.5 | 2.50.098 | 0.70.028 | 1.30.051 | 1.50.059 | 40 | Trapezoidal | 4, 6, 10 mm |
| T5 | 50.197 | 1.20.047 | 2.20.087 | 2.650.104 | 40 | Trapezoidal | 6, 10, 16, 25 mm |
| T10 | 100.394 | 2.50.098 | 4.50.177 | 5.30.209 | 40 | Trapezoidal | 16, 25, 32, 50 mm |
| T20 | 200.787 | 50.197 | 80.315 | 10.150.400 | 40 | Trapezoidal | 32, 50, 75, 100 mm |
| Trapezoidal, metric AT (reinforced) | |||||||
| AT5 | 50.197 | 1.20.047 | 2.70.106 | 2.50.098 | 50 | Trapezoidal | 10, 16, 25, 32 mm |
| AT10 | 100.394 | 2.50.098 | 50.197 | 50.197 | 50 | Trapezoidal | 16, 25, 32, 50 mm |
| Curvilinear HTD (ISO 13050) | |||||||
| HTD 3M | 30.118 | 1.20.047 | 2.40.094 | — | — | Curvilinear (round) | 6, 9, 15 mm |
| HTD 5M | 50.197 | 2.10.083 | 3.80.150 | — | — | Curvilinear (round) | 9, 15, 25 mm |
| HTD 8M | 80.315 | 3.40.134 | 5.60.220 | — | — | Curvilinear (round) | 20, 30, 50, 85 mm |
| HTD 14M | 140.551 | 60.236 | 100.394 | — | — | Curvilinear (round) | 40, 55, 85, 115, 170 mm |
| Gates PowerGrip GT2 / GT3 | |||||||
| GT2 2 mm | 20.079 | 0.710.028 | 1.520.060 | — | — | Modified curvilinear | 3, 6, 9 mm |
| GT2 3 mm | 30.118 | 1.120.044 | 2.410.095 | — | — | Modified curvilinear | 6, 9, 15 mm |
| GT2 5 mm | 50.197 | 1.920.076 | 3.810.150 | — | — | Modified curvilinear | 9, 15, 25 mm |
| STD / Super Torque (S..M) | |||||||
| S2M | 20.079 | 0.760.030 | 1.360.054 | — | — | Curvilinear, flat tip | 4, 6, 10 mm |
| S3M | 30.118 | 1.140.045 | 1.90.075 | — | — | Curvilinear, flat tip | 6, 10, 15 mm |
| S5M | 50.197 | 1.910.075 | 3.40.134 | — | — | Curvilinear, flat tip | 10, 15, 25 mm |
| S8M | 80.315 | 3.050.120 | 5.30.209 | — | — | Curvilinear, flat tip | 15, 25, 40, 60 mm |
No exact match. The nearest sizes:
How to identify a belt and read its code
Measure the pitch over many teeth. Count 10 teeth and measure from the first to the eleventh tooth centre, then divide by 10: 50.8 mm = 5.08 mm = XL, 50 mm = a 5 mm pitch (T5, AT5, HTD 5M, GT2 5 mm or S5M), 20 mm = a 2 mm pitch. Then look at the tooth: straight flanks are trapezoidal (T, AT, XL…), round teeth are HTD, round teeth with a shallower, wider shape are GT, and a rounded tooth with a small flat on the tip is STD. A deep, broad trapezoid with a 5 mm pitch is AT5 rather than T5.
Inch belts are coded length–profile–width: 240XL037 is 24.0" pitch length (the number is tenths of an inch), XL pitch, 0.37" (3/8") wide; 225L050 is 22.5", L, 1/2" wide. HTD and GT belts are coded length–pitch–width in mm: 800-5M-15 is 800 mm pitch length, 5 mm HTD, 15 mm wide; Gates writes GT2 as 800-5MGT-15 (or 5GT). T belts are written T5-500 or 16 T5/500 (width, profile, length). Divide the pitch length by the pitch to get the tooth count: 800 / 5 = 160 teeth.
The pitch length is measured on the belt's pitch line, which runs through the tension cord, not on the back or the teeth. The pulley's pitch diameter is therefore larger than its outside diameter by twice the pitch line differential (PLD): PD = z × p / π, OD = PD − 2u.
About Timing Belts
A synchronous belt transmits motion by tooth engagement, so it keeps exact timing without slip, like a chain but quieter and without lubrication. The profile families in this chart are not interchangeable even at equal pitch: trapezoidal teeth (MXL, XL, T5…) concentrate stress at the tooth root; curvilinear HTD teeth spread it and carry considerably more load than trapezoidal belts of similar pitch and width; GT and STD profiles refine the curve further for lower backlash and less noise.
Heights are nominal. The tooth height of a profile is fixed by its pulley geometry, but the overall belt height depends on the backing and cord, and catalogues differ by a few tenths of a millimetre (HTD 8M is 5.6 mm in Gates' tables and 6.0 mm in several others; AT10 is listed at 4.5–5.0 mm). Use the value of your belt's maker when the belt runs over a tensioner, a guide or a backside idler.
The 3D printer belt is the GT2 2 mm pitch belt, 6 mm wide, with 16- or 20-tooth pulleys (PD 10.19 mm / 12.73 mm). Many generic "GT2" belts are close copies of the Gates 2MGT profile with slightly different heights (often 1.38 mm overall, 0.75 mm tooth); they run on generic GT2 pulleys. Don't use a 2 mm trapezoidal (T2) or MXL pulley with them.
PowerGrip, GT2 and GT3 are trademarks of the Gates Corporation; HTD was developed by Uniroyal and is now an industry-standard profile (ISO 13050 defines the H-type curvilinear profiles); STD/Super Torque profiles are made under various brand names (STS, STPD).
Choosing a profile
For new metric designs, HTD 5M/8M or GT2 3/5 mm are the default: wide choice of stock pulleys and higher power than T5/T10 at the same width. T and AT belts are mostly polyurethane with steel cords and are used in linear axes and conveyors, often as open-ended belt cut to length. Inch trapezoidal belts (XL, L, H) remain common on older machinery, sewing machines and in the US. MXL and 2 mm GT2 cover small instruments, printers and positioning stages.
Minimum pulley size
Every profile has a minimum pulley size below which the cord is over-bent, roughly 10–16 teeth for the small pitches and 22–28 teeth for HTD 8M and 14M. Take the exact figure from the belt maker's table. At least six teeth should be in mesh on the small pulley; the calculator below warns when there are fewer.
Questions
What is the pitch of a GT2 belt?
2 mm for the common 3D-printer GT2 belt. Gates also makes GT2/GT3 in 3 mm, 5 mm and 8 mm pitch. A 20-tooth GT2 pulley has a pitch diameter of 20 × 2 / π = 12.73 mm.
Is HTD 5M the same as GT2 5 mm or T5?
No. All three have a 5 mm pitch, but the tooth shapes differ: T5 is trapezoidal, HTD 5M round, GT2 5 mm a shallower modified curve. Use the pulley made for the belt profile.
How do I calculate the length of a timing belt?
For two pulleys: L = 2C + π(D1 + D2)/2 + (D2 − D1)² / (4C), with pitch diameters D = teeth × pitch / π and C the centre distance. Then round to a whole number of teeth (L / pitch) and recalculate C. The calculator above does both.
What does 240XL037 mean?
240 = 24.0" pitch length, XL = 1/5" (5.08 mm) pitch, 037 = 0.37" (3/8", about 9.5 mm) wide. The belt has 24.0 / 0.2 = 120 teeth.
What is the difference between T5 and AT5?
Both are metric trapezoidal 5 mm pitch belts. AT5 has a wider tooth with a 50° flank angle and a thicker belt (about 2.7 mm against 2.2 mm), so it carries more load and has less backlash. They need different pulleys.
Sources
- ISO 5296:2012, Synchronous belt drives. Belts with pitch codes MXL, XXL, XL, L, H, XH and XXH
- ISO 13050:2014, Curvilinear toothed synchronous belt drive systems (HTD-type profiles)
- Gates: Industrial Power Transmission Preventive Maintenance manual (belt profile table)
- Optibelt: ALPHA POWER polyurethane timing belts, product range (T and AT profiles)
- Optibelt: Technical manual, rubber timing belt drives (STD, HTD, trapezoidal)
- Pfeifer Industries: Timing belt tooth profiles and pitches
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.