Electric Motor Frame Size Chart: IEC 56–355 and NEMA 42–449T

A motor frame size fixes the mounting dimensions, not the power. In IEC frames the number is the shaft height in mm (frame 132 = 132 mm); in NEMA frames the first two digits divided by 4 give the shaft height in inches (254T = 25/4 = 6.25 in). Two motors of the same frame bolt to the same base and line up with the same coupling.

48 framesChecked 2026-11-156 sources
Shaft heights on one logarithmic scale (mm). Frames that line up are the closest IEC/NEMA pairs. Tap a frame.Proportions shown, not to scale

Motor framesTap a frame for its drawing and dimensions

48 of 48 frames
FrameHShaft height (IEC H / NEMA D)mminmm · inAFoot holes across (IEC A / NEMA 2E)mminmm · inBFoot holes along (IEC B / NEMA 2F)mminmm · inCShaft shoulder to first hole (IEC C / NEMA BA)mminmm · inKFoot bolt hole (IEC K / NEMA H)mminmm · inDShaft diameter (IEC D / NEMA U)mminmm · inEShaft extension (IEC E / NEMA N-W)mminmm · inShaft diameter, 2-pole (IEC)mminmm · inShaft extension, 2-pole (IEC)mminmm · in
IEC 60072-1 (mm)
56562.205903.543712.795361.4175.80.22890.354200.787——
63632.4801003.937803.150401.57570.276110.433230.906——
71712.7951124.409903.543451.77270.276140.551301.181——
80803.1501254.9211003.937501.969100.394190.748401.575——
90S903.5431405.5121003.937562.205100.394240.945501.969——
90L903.5431405.5121254.921562.205100.394240.945501.969——
100L1003.9371606.2991405.512632.480120.472281.102602.362——
112M1124.4091907.4801405.512702.756120.472281.102602.362——
132S1325.1972168.5041405.512893.504120.472381.496803.150——
132M1325.1972168.5041787.008893.504120.472381.496803.150——
160M1606.299254102108.2681084.25214.50.571421.6541104.331——
160L1606.29925410254101084.25214.50.571421.6541104.331——
180M1807.08727910.9842419.4881214.76414.50.571481.8901104.331——
180L1807.08727910.98427910.9841214.76414.50.571481.8901104.331——
200L2007.87431812.52030512.0081335.23618.50.728552.1651104.331——
225S2258.85835614.01628611.2601495.86618.50.728602.3621405.512——
225M2258.85835614.01631112.2441495.86618.50.728602.3621405.512552.1651104.331
250M2509.84340615.98434913.7401686.614240.945652.5591405.512602.3621405.512
280S28011.02445717.99236814.4881907.480240.945752.9531405.512652.5591405.512
280M28011.02445717.99241916.4961907.480240.945752.9531405.512652.5591405.512
315S31512.4025082040615.9842168.504281.102803.1501706.693652.5591405.512
315M31512.4025082045717.9922168.504281.102803.1501706.693652.5591405.512
315L31512.40250820508202168.504281.102803.1501706.693652.5591405.512
355M35513.97661024.01656022.04725410281.102953.7401706.693752.9531405.512
355L35513.97661024.01663024.80325410281.102953.7401706.693752.9531405.512
NEMA MG 1 (inch)
4266.72 5/888.93 1/242.91.68852.42.0627.19/329.53/828.61 1/8——
4876.231084 1/469.92 3/463.52 1/28.711/3212.71/238.11 1/2——
56 (NEMA)88.93 1/2123.84 7/876.2369.92 3/48.711/3215.95/847.61 7/8——
143T88.93 1/2139.75 1/2101.6457.22 1/48.711/3222.27/857.22 1/4——
145T88.93 1/2139.75 1/2127557.22 1/48.711/3222.27/857.22 1/4——
182T114.34 1/2190.57 1/2114.34 1/269.92 3/410.313/3228.61 1/869.92 3/4——
184T114.34 1/2190.57 1/2139.75 1/269.92 3/410.313/3228.61 1/869.92 3/4——
213T133.45 1/4215.98 1/2139.75 1/288.93 1/210.313/3234.91 3/885.73 3/8——
215T133.45 1/4215.98 1/2177.8788.93 1/210.313/3234.91 3/885.73 3/8——
254T158.86 1/425410209.68 1/41084 1/413.517/3241.31 5/8101.64——
256T158.86 1/425410254101084 1/413.517/3241.31 5/8101.64——
284T177.87279.411241.39 1/2120.74 3/413.517/3247.61 7/8117.54 5/8——
286T177.87279.411279.411120.74 3/413.517/3247.61 7/8117.54 5/8——
324T203.28317.512 1/2266.710 1/2133.45 1/416.721/32542 1/8133.45 1/4——
326T203.28317.512 1/2304.812133.45 1/416.721/32542 1/8133.45 1/4——
364T228.69355.614285.811 1/4149.25 7/816.721/3260.32 3/8149.25 7/8——
365T228.69355.614311.212 1/4149.25 7/816.721/3260.32 3/8149.25 7/8——
404T25410406.416311.212 1/4168.36 5/820.60.813732 7/8184.27 1/4——
405T25410406.416349.313 3/4168.36 5/820.60.813732 7/8184.27 1/4——
444T279.411457.218368.314 1/2190.57 1/220.60.81385.73 3/8215.98 1/2——
445T279.411457.218419.116 1/2190.57 1/220.60.81385.73 3/8215.98 1/2——
447T279.411457.21850820190.57 1/220.60.81385.73 3/8215.98 1/2——
449T279.411457.21863525190.57 1/220.60.81385.73 3/8215.98 1/2——

How to read a frame designation

IEC: number + letter. The number is the shaft height H in mm (56 to 400 in IEC 60072-1). The letter is the foot length: S short, M medium, L long. 132S and 132M have the same height, shaft and A, but B is 140 mm against 178 mm.

IEC mounting codes (IEC 60034-7) are separate: B3 foot, B5 flange (FF), B14 face (FT), B35 foot + flange. A 100L B5 motor has the 100L shaft and an FF215 flange.

NEMA: digits + letters. For integral-hp T frames the first two digits ÷ 4 = shaft height D in inches (182T → 18/4 = 4.5 in). The third digit indicates foot length: 143T and 145T share everything except 2F (4.0 vs 5.0 in).

NEMA suffixes: T current standard (1964 rerate); U the older, larger 1952 frames; TS short shaft for belt-free direct coupling; C C-face; D D-flange; J jet pump; Y special mounting. 42, 48 and 56 are fractional-hp frames without T.

Letters differ, meanings match. IEC H, A, B, C, K, D, E correspond to NEMA D, 2E, 2F, BA, H, U, N-W. Note that IEC D is shaft diameter while NEMA D is shaft height.

About Motor Frame Sizes

Frame dimensions let you replace a motor from any maker without changing the base, the coupling or the belt alignment. Power is not part of the frame: a 4-pole 132S motor is typically 5.5 kW and a 2-pole one 7.5 kW, and high-efficiency (IE3/IE4) motors sometimes move up a frame. Always match the frame and shaft, then check power and speed on the nameplate.

IEC frames are metric throughout. Shafts of 2-pole motors are smaller from frame 225 upwards because the torque is lower for the same power; the table lists both. Keys follow ISO R773 / DIN 6885 (see parallel keys); shaft tolerances are j6 up to 28 mm, k6 from 38 to 48 mm and m6 above.

NEMA frames are inch-based. A NEMA motor cannot simply replace an IEC motor even when the shaft heights look close: 132 mm against 5.25 in (133.35 mm) for a 213T is near, but the shaft diameter (38 mm against 1-3/8 in = 34.9 mm) and the hole pattern differ. Adapter bases and bushings exist for exactly this reason.

Values are the standard mounting dimensions. Overall length, height to the top of the terminal box and weight depend on the manufacturer; take those from the maker's dimension drawing.

Nearest IEC and NEMA frames

Approximate equivalents by shaft height. Holes and shafts differ, so treat them as a starting point for an adapter plate, not a drop-in swap.

IECH (mm)NEMAD (in / mm)
8080483.0 / 76.2
90S/L9056, 143T/145T3.5 / 88.9
112M112182T/184T4.5 / 114.3
132S/M132213T/215T5.25 / 133.4
160M/L160254T/256T6.25 / 158.8
180M/L180284T/286T7.0 / 177.8
200L200324T/326T8.0 / 203.2
225S/M225364T/365T9.0 / 228.6
250M250404T/405T10.0 / 254
280S/M280444T–449T11.0 / 279.4

Typical power by frame (4-pole, 50 Hz, IEC)

Typical ratings of standard IE2/IE3 totally enclosed fan-cooled motors; these come from manufacturer catalogues (IEC 60072-1 output tables are no longer binding) and vary between makers.

FrameTypical 4-pole power
710.25–0.37 kW
800.55–0.75 kW
90S / 90L1.1 / 1.5 kW
100L2.2–3 kW
112M4 kW
132S / 132M5.5 / 7.5 kW
160M / 160L11 / 15 kW
180M / 180L18.5 / 22 kW
200L30 kW
225S / 225M37 / 45 kW
250M55 kW
280S / 280M75 / 90 kW
315S / M / L110 / 132 / 160–200 kW

Questions

How do I find the frame size of a motor?

It is on the nameplate (FRAME or FR). If the plate is missing, measure the shaft height from the bottom of the feet to the shaft centre: in mm it is the IEC frame number (132 mm → 132), in inches multiply by 4 for the first two NEMA digits (5.25 in → 21x). Then measure the foot hole spacing to tell S/M/L or the third NEMA digit.

What is the shaft height of a 56 frame motor?

A NEMA 56 frame has a shaft height of 3.5 in (88.9 mm) and a 5/8 in shaft. An IEC 56 frame is 56 mm high with a 9 mm shaft. Same number, very different motor.

What does the T mean in 182T?

T marks the current NEMA standard frames introduced in 1964 (the "T-frame rerate"), which are smaller for the same power than the older U frames. 182T: shaft height 4.5 in, shaft 1-1/8 in.

What is the difference between 132S and 132M?

Only the foot length: hole spacing B is 140 mm for 132S and 178 mm for 132M. Shaft height (132 mm), shaft (38 × 80 mm) and A (216 mm) are the same.

Can I replace an IEC motor with a NEMA motor?

Not directly. Shaft heights can be close (IEC 160 = 160 mm, NEMA 254T = 158.75 mm) but shaft diameters, keys and hole patterns differ. Use an adapter base and change the coupling half or pulley bore.

Sources

  1. IEC 60072-1:2022, Dimensions and output series for rotating electrical machines, Part 1: Frame numbers 56 to 400
  2. NEMA MG 1: Motors and Generators, Part 4 (dimensions, frame designations)
  3. Regal Rexnord: Quick reference motor dimensions (NEMA frame chart)
  4. Motion Industries: NEMA quick reference chart
  5. Electric Motor Warehouse / Drive Centre: IEC quick reference dimensional charts
  6. ABB / WEG / Brook Crompton low-voltage motor catalogues: IEC dimension tables

Values last checked against these sources on November 15, 2026. · How we check data

Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.